Lovibond Maxi Direct Скачать руководство пользователя страница 102

Страница: 102 / 268

100

MaxiDirect_2c 03/2010

1.1 Methods

Hydrogen peroxide

with tablet reagent

0.03 – 3 mg/l H

1. Fill a clean vial (24 mm Ø) with

10 ml of the water

sample

, close tightly with the cap.

2. Place the vial in the sample chamber making sure that

the marks are aligned.

3. Press

ZERO

key.

4. Remove the vial from the sample chamber and

empty it,

leaving a few drops remaining in the vial

5. Add

one HYDROGENPEROXIDE LR tablet

straight

from the foil and crush the tablet using a clean stir-

ring rod.

6. Add water sample to the 10 ml mark.

7. Close the vial tightly with the cap and swirl several times

until the tablet is dissolved.

8. Place the vial in the sample chamber making sure that

the marks are aligned.

9. Press

TEST

key.

Wait for a

reaction period of 2 minutes

After the reaction period is finished the measurement

starts automatically.

The result is shown in the display in mg/l Hydrogen

peroxide.

Countdown
2:00

prepare Zero
press ZERO

Zero accepted
prepare Test
press TEST

Содержание Maxi Direct













































































































































































































































































Результаты поиска

Содержание Maxi Direct

Отзывы:

Lovibond Maxi Direct, Инструкция по эксплуатации, Страница: 102 / 268

Результаты поиска

Содержание Maxi Direct

Отзывы: