background image

IMPORTANT NOTICE

When this equipment is used as part of an 
audio monitoring system, the law requires 
that  the  public  be  given  notice  of AUDIO 
MONITORING  ON  THE  PREMISES.    A 
decal  notice  is  included  with  each 
microphone shipped.

Federal Law References:
Federal  Regulations,  US  Code,  Title  18.   
Crime and Criminal Procedure, Sec 2510.

DG-25III and DG-MA

SOUND ACTIVATED BASE STATION 

WITH MONITOR AMPLIFIER

INSTALLATION AND OPERATING INSTRUCTIONS

2 Conductor 

shielded

 cable, 22 

gauge with a 24 gauge drain wire

NOTE:

Unshielded cable is not 

satisfactory for audio systems

WIRING REQUIREMENTS

West Penn 452 or equivalent

WIRING REQUIREMENTS

4 Conductor consisting of:

+ 2 Conductor 

shielded

, 20  gauge 

with 22 gauge drain (microphone 
connection)

+ 2 Conductor 

unshielded

, 18 gauge 

(speaker connection)

All in the same jacket

West Penn 356 or equivalent

MODEL DG-25

III

Sound Activated Base Station

MODEL DG-MA

Monitor/Amplifier

FOR ONE-WAY LISTEN 

FOR TWO-WAY TALK/LISTEN 

6955 VALJEAN AVE, VAN NUYS, CA 91406

PH:  (818)994-6498 / FAX: (818)994-6458

 / www.louroe.com

[email protected]

®

AUDIO 

MONITORING

On 

These Premises

®

dg_25_inst_1/12

Содержание DG-MA

































Отзывы: