LNE3003 Quick Setup Guide - English - R2
Time: 10 Minutes Hand Tools Skills - Easy
BASIC INSTALLATION GUIDE
SET UP YOUR CAMERA FIRST
STEP 1
Place the base of the
camera on a fl at surface
and screw on the stand.
a
Attach the screw knob to
the camera stand.
b
Attach the wireless antenna to
the back of the camera.
c
Screw the camera to the
camera stand.
d
Tighten the screw knob to
secure the camera.
e
DISCOVER & VIEW YOUR CAMERA
ON THE LOCAL NETWORK
STEP 2
Time: 10 Minutes Hand Tools
- Computer
Skills - Easy
BASIC INSTALLATION GUIDE
NOTE: This quick start guide refers to a Windows Vista™, installation.
Pop-up security windows may differ in Windows XP™. Installation is
easy in both versions of the operating system.
NOTE: For initial setup, you will need Internet Explorer as your
default browser. Do not install DigiConsole until Step 2 is completed.
Launching the DigiConsole Software
Before launching the program, please make sure your computer is connected
to the same local network as the camera and has access to the Internet.
The camera must be connected using the included Ethernet cable for initial
installation. It is recommended to setup the camera when your computer is
wired to the local network. If you are using the wireless connection on your
computer, please make sure you are connected to your wireless router (check
wireless name - SSID).
If the software runs
automatically, please
proceed to Step 2, section d.
If the pop-up window
appears, click Run
DigiConsole.exe and
continue to Step 2, section c.
b
Double-click the camera to
launch DigiViewer in your
browser.
a
Enter admin in the username
and admin in the password
fi elds to access your camera.
The browser will prompt you
to install ActiveX.
b
Depending on your browser
security settings, you can use the
“remember me” check option and
the next time you will view the
same camera using this browser
it will renumber user name and
password till you restart your
computer.
Did you know?
If a security pop-up window
appears, click Unblock
and Continue to allow
DigiConsole to run.
c
NOTE: If the CD does not start
automatically, please go to “Computer”
(“My Computer” for Windows XP™ users)
and double click on the CD Drive to run
the application. Follow Step 2.
Click Find to discover Lorex
cameras on your network.
OPTION: If UPNP is enabled on your
computer open the “Network” (“My
Network Places” for Windows XP™
users) folder to view UPnP devices.
(UPNP is disabled by default in
Windows Vista™).
d
RECORD AND PLAYBACK YOUR CAMERA
ON THE LOCAL NETWORK
STEP 3
LNE3003
Quick Setup Guide
+VTGCNN[KUVJCVGCU[
• Remote Surveillance Camera,
• Antenna
• Camera stand (base, stand and
screw knob)
• Masonary Plugs & Screws
• Power Adaptor
• Ethernet Cable
• Quick Start Guide
• Software CD (includes manuals)
PACKAGE CONTENTS:
a
Insert the included
DigiConsole Software CD into
your CD/DVD-ROM drive.
Plug the power adaptor into the
power port on the bottom of the
camera. Plug the other end to an
electrical outlet.
NOTE: Make sure the LED is lit
on the front of the camera. If not,
check that all cables are properly
connected.
g
Set up Your Camera
Time: 10 Minutes
Skills - Easy
BASIC INSTALLATION GUIDE
Hand Tools
- Computer
Local Viewing
Congratulations! Your camera is
now set-up for local viewing
d
If a security pop-up window
appears, click Unblock
and Continue. Click the
warning on the browser bar
and select Install ActiveX
Control. Click Unblock or
Continue in any proceeding
security pop-ups.
c
Click the warning bar (it will turn from
yellow to blue) and select Install ActiveX.
Click Install to start the
installation. Click Unblock or
Continue in any security
pop-up. (This step is required
only for fi rst time set-up).
2
1
4
3
1. Camera
2. Antenna
3. Power Adaptor Port
4. Ethernet Cable (LAN) Port
5. Reset
5
BEFORE YOU START
This Network Camera is designed for easy installation.
However, before you continue, please read the following:
The Quick Start Guide must be followed in sequence without
skipping steps.
1. When setting up the camera, use Internet Explorer only
.
After the initial setup, you can view the camera using Internet
Explorer or later (with ActiveX), Mozilla Firefox, Safari, and Google
Chrome
2. Steps 1 - 3 should to be completed and your camera must be
connected wired before connecting the camera wirelessly.
3. When connecting the camera to a wireless network, consider the
following:
a. If your wireless router is not set up with wireless encryption, you
can start the installation process immediately.
b. If your wireless router is set up with encryption, note that Wi-Fi
wireless encryption supports only WEP open mode key (64 &
128bit).
c. If your wireless router is set up with the supported encryption
type mentioned above, please make sure you know the encryption
key. If you do not know the encryption key (encryption password),
please refer to your router’s manual in order to reset the key.
d. If your wireless router is set up with a different type of encryption
please refer to your router’s manual in order to change
encryption type to WEP.
e. The camera is compatible with Macintosh for viewing only.
Recording on Macintosh is not supported. To set up camera using
Macintosh, advanced knowledge is required. Please refer to
“Setting Up Using Macintosh” FAQ on LOREX web site
www.lorexcctv.com
f
Connect the included network
cable to the LAN port on the
bottom of the camera. Connect
the other end of the network
cable to the router, switch, or
active wall port of your local
network.
IMPORTANT
Playback
Click Playback, if viewing
or recording is enabled on
DigiConsole, you will be prompted
to stop live viewing. Click OK.
a
b
Select the desired cameras and
recording date from the list to
play. Right click and select Play
Back Recorded Video.
Use DigiConsole to playback (repeat Step 2, sections a - c to run from CD).
Your default player (e.g.
Windows Media Player) will
play the selected video.
c
Recording
(Video Only)
NOTE: Playback requires Windows Media Player and Xvid codec. A link to Xvid can be
found on the Home page of DigiConsole.
Use DigiConsole to record (repeat Step 2, sections a - c to run from CD).
Click Install to start the
installation in the DigiConsole.
a
b
Click Next at the bottom right
corner and when asked, read and
accept the license.
The process takes few minutes.
Click OK to proceed with
installation.
c
Double click to open the
DigiConsole icon from your
desktop.
e
f
Find and detect your camera
(Step 2, section d)
Right click the camera icon
and select View live video.
Wait till you see the streaming
video.
g
d
Click the red
X
on top right corner
to close DigiConsole.
h
Right click the camera icon
and select Record Video
Image. You are now recording
on to your local computer.
NOTE: DigiConsole supports up to 6 cameras
and include basic recording option (ON or
OFF only). For advanced software DIGIplayer
please visit our web www.lorexcctv.com
Broadband Router and Computer
are required for local and remote
monitoring (not included).
Congratulations! Your
camera is now ready to
record and playback on the
local network
