LORD D1 Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 44

LORD D1 Скачать руководство пользователя страница 33

4.18 Replacing door hinge

Prerequisite:

Appliance is disconnected from power supply.

Appliance is disconnected from water supply.

Appliances is freely accessible.

Side panel has been removed.→

Outer door has been removed.

Inner door has been removed.

Control panel has been removed.→

Door spings has been fixed.→

Toe panel has been removed.→

Base socket plate has been removed.→

Overflow channel has been removed.→

4.18.1 Removing door hinge

1.

1.

Release catch hook with a screwdriver(1).

2.

Pull door hinge forwards (2).

2.

Release ground connection on door hinge.

4.18.2 Installing door hinge

Danger

Risk of electric shock due to live parts!

Danger to life through electric shock in case of improper repair

▶

Electric parts should be repaired by a qualified electricians.

▶

After the repair have a safety test according VDE 0701 or country-
specific regulations performed.

Repair

«
...
31
32
33
34
35
...
»

Содержание D1













































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды