LORCH P-Basic Скачать руководство пользователя страница 63

Страница: 63 / 68

Troubleshooting

- 63 -

02.20

909.2710.1-06

9.14 Service Codes

Via menu Extras, Lock function special Service codes can be entered to enanble or disable different func-

tions.

code

function

displayed message

644

reset the three-digit code of the lock function to “000”

Code = 0

660

activate TIG mode selection

TIG mode On

661

deactivate TIG mode selection

TIG mode Off

663

deactivate PE protection

PEC control Off

664

activate PowerMaster buttons

Powermaster On

665

deactivate gas pressure switch monitoring

Gas monitor. Off

666

deactivate PowerMaster buttons

Powermaster Off

668

ac/- 10% correction at Tiptronic with lock level 2 or 3

PlusMinus10% On

669

deac/- 10% correction at Tiptronic with lock level 2 or 3

PlusMinus10% Off

670

activate US units

US units On

671

deactivate US units

US units Off

Entering the Codes

–

enter menu Extras, Lockfunction

–

press button material (minus) or button gas (plus)

–

acknowledge the question „Change Parameter?“ with button “arrow up”

–

press button minus or plus

–

enter the code number with the encoder of the front panel

–

acknowledge with button “arrow down”

Содержание P-Basic





































































Результаты поиска

Содержание P-Basic

Отзывы:

Бренды по названию

Популярные бренды

LORCH P-Basic, Руководство по обслуживанию

Результаты поиска

Содержание P-Basic

Отзывы:

Бренды по названию

Популярные бренды