LORCH P-Basic Скачать руководство пользователя страница 56

Страница: 56 / 68

Troubleshooting

- 56 -

02.20

909.2710.1-06

9.7

Monitoring wire feed motor

The pc-board DMR has it‘s own microcontroller which is responsible for driving, controlling and monitoring

the wire feed motor.

Schematic

The current consumption and the tacho signal of the motor are monitored by the microcontroller. If the

current consumption of the motor is too high (e.g. if wire feed unit is blocked mechanically) or if the tacho

is not connected, the machine will stop and displays

E08

(wire feed / tacho).

The DMR and the MAPRO are communicating via the CAN bus with the Master. If the communication is

interfered or jammed, the machine will stop and displays also

E08

Is one of the CAN bus wires is disconnected (loose connection) between MAPRO and DMR, the display (con-

nected to the DMR) is only showing a “

”.

Содержание P-Basic





































































Результаты поиска

Содержание P-Basic

Отзывы:

Бренды по названию

Популярные бренды

LORCH P-Basic, Руководство по обслуживанию

Результаты поиска

Содержание P-Basic

Отзывы:

Бренды по названию

Популярные бренды