manualshive.com logo in svg

LORCH MicorMIG 300, Руководство по обслуживанию

Поделиться
Скачать
LORCH MicorMIG 300 Скачать руководство пользователя страница 61

page 61

Measuring CAN bus

The CAN bus is easily checked at each pc-board by measuring the resistance value between CAN-low and 

CAN-high against GND (ground). Before measuring, disconnect the pc-board completely from the machine.

If the measuring result is too low (1k ohm or lower), the CAN controller chip is damaged and the pc-board must be 

exchanged.

Measuring the CAN bus at the MAPRO

Result: about 60k ohm each

CAN_LOW

GND

CAN_HIGH

Measuring the CAN bus at the front panel

Result: 50k ohm - 60k ohm each

CAN_LOW

GND

CAN_HIGH

Measuring the CAN bus at the DMR-RT3

Result: about 490k ohm each

CAN_LOW

GND

CAN_HIGH

Measuring the CAN bus at the DMRPP05 (Push-Pull DMR) is different, there the result is about 0.9k 

ohm by standard. A faulty CAN controller chip may not be directly detecable.

Since week12 2017, CAN controllers with a higher dielectric strength are used on all pc-boards.

Содержание MicorMIG 300





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды