Cut the cable (27) into two pieces of equal length (30 cm), then
remove the insulation of both ends of both parts (approx. 3 mm) and
tin-plate it. Prepare another piece (length: 3 cm) the same way. Be
careful, the cable can easily be torn!
Shorten that lead of the diode (24) where the black ring is tending to
up to a length of approx. 3 mm. Solder one of the cables of 30 cm of
length on the diode. Black ring should tend to the cable. Then insula-
te the junction with black shrink-tube (29). Shrink on with hair-drier
or hot-air-gun. [Fig. 1]
1.
2.
Made for:
Lokshop eK
Froschhöhle 9
D - 76229 Karlsruhe
Tel.: +49721/490350
Fax: +49721/4903520
E-Mail: [email protected]
Dieses Produkt ist
kein Spielzeug.
Nicht geeignet für
Kinder unter 14
Jahren!
This product is not
a toy.
Not suitable for
children under 14
years!
Ce produit n'est
pas un jouet.
Ne convient pas
aux enfants de
moins de 14 ans!
D
GB
F
Semaphore Home Signal, 1:220 (Z)
Hp0/Hp2 two arms
Item No LS4801
Item N
o
LS4800
Safety advices
This kit contains small parts which can easily be swallowed by children. Not
suitable for children under 14 years!
The electric and electronic components may only be run with approved
low-voltage transformers. The components are sensitive to heat and may
only be exposed to high temperatures for a short time. Do not “roast”!
A soldering iron develops temperatures up to 400°C. Do not leave it unat-
tended! Keep distance to combustible materials and use a heat-resistant
base-pad for work. Any electrical connection-work may only be done when
disconnected from the main power supply.
All sources of current must be secured against short-cut in order to prevent
fire. Resistors are necessary for regular function. Lamps run without resis-
tors will be destroyed. Resistors may not be covered with insulating materi-
als in order to guarantee sufficient cooling.
The following instructions should be
read carefully!
Content:
The following tools are required:
Small edge cutter
Flat pliers and pointed tweezers
Soldering iron with thin tip, solder (pref. Ø 0,5 mm)
Superglue
signal mast
base plate
mast top
imitation of lantern-winch
imitation of drive casing,
front wall
imitation of drive casing,
back wall
post plate, long
post plate, short
socket of positioning-wire
signal arm, long
positioning mechanism
front of lantern-case.
back part of lantern-case
base of lantern-case
filter-lens, white
f
ilter-lens, green
filter-lens, red
lantern-screen, two holes
signal arm, short
filter-lens, yellow
lantern-screen, one hole
circuit-board with 2 LED,
green/red
circuit-board with 1 LED,
yellow
diode 1N4148 or similar
resistor, 820Ω
(grey-red-brown-gold)
Without illustration:
positioning wire
cable
labels
shrink-tube, black
shrink-tube, yellow
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
1
3
4
5
6
7
8
9
10
11
12
14
13
15
16
17
18
19
20
21
22
23
25
24
3
7
9
11
10
16 17 18
1
5
6
4
for
29
12 14
13
15
8
13
14
12
15
19
20 21
26
27
28
29
30
Assembly:
For a better control, you can tick each finished work-step in a box at the
left side of the text.
24
25
22
23
2
Signal Kit
Please check at first if the kit is complete. In case of damaged or
missing parts due to the sellers improper packing, please send
back the whole package.
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
10 - 16 V, DC/AC
Congratulations!
You have bought a high-quality product, supposed to give pleasure during
assembly and use. Please read these instructions carefully before assemb-
ling or using the product and check if the content of the packaging is com-
plete.