background image

User Manual 

 

 

CBX-1 / CBX-2 

 

 

 

 
 

1. Preface 

Dear customer, 
 
Thank you for choosing a 

CBX-1 / CBX-2 

motor control box for height adjustable 

desks from 

LOGICDATA GmbH

. . You have purchased a state-of-the-art product 

which complies with all safety requirements. 

1.1. Appropriate Operation 

CBX-1 / CBX-2 motor control boxes must solely be used for the intended application 
of control of height-adjustable desks. Only motors which meet the specifications of 
LOGICDATA GmbH must be used to drive lifting columns. The control box must be 
installed, initially operated and functionally tested by competent personnel only. Use 
other than described above is only allowed with permission of LOGICDATA. The 
basic functionality is up/down movement of the desk (doable with any handset). 

1.2.  Functionality CBX-1 / CBX-2 

The motor control boxes CBX-1 / CBX-2 offer following functionality and performance 
characteristics (however, the practical application of these functions depends on the 
used handset): 
 

• 

Control Boxes are available for different mains voltages 

• 

Broad Range of handsets available from LOGICDATA  

• 

Depending on type of the handset additional functionality (e.g. saving and 
accessing memory positions, etc.) is available 

• 

Configurable stop conditions (overcurrent, timeout, limit switches) 

• 

Configurable reset conditions 

• 

Configurable duty cycle 

• 

Optional mains cut-off 

• 

PLUG DETECTION 

• 

Up to 4 Memorypositions 

• 

Pinch protection with optional squeeze line  

• 

DRIVE-BACK function on various conditions 

Page 3/29 

Содержание CBX-1






























Отзывы: