background image

User Manual 

 

 

CBX-1 / CBX-2 

 

 

4.2.5.  Activation of the End Position Alignment Procedure 

Activating the end position alignment procedure lies within the scope of initial 
operation carried out by a service technician. 

 

1. 

 

 o. 

 

Press and hold keys 

desk up 

and

 desk down

 (or 

alternatively the 

S

 key) 

simultaneously

 for about 5 

seconds until the control box clicks once. 

2. 

 

Press key 

desk up

 until the control box clicks once. 

3. 

 

Press key 

desk up 

again until the control box clicks 

once. 

4. 

 

Press key 

desk up

 again until the control box double-

clicks. 

 

4.2.6.  End Position Alignment 

The end position alignment procedure has to be carried out on initial operation after 
the control box has been installed correctly. 

 

 

Note:

 Selectively, all configurations needed for initial operation can be 

factory-made. 

 

 
To align the end positions, proceed as follows: 

 

1. 

 

The display reads 

068

2. 

 

Press and hold key 

desk down

 until the desk has 

reached the lower end position. 

3. 

 

Press and hold key 

desk up 

until the desk has reached 

the upper end position. 

4. 

 

Confirm the setting by pressing key 

desk down

 

Page 17/29 

Содержание CBX-1






























Отзывы: