Function Programming
Steps
Remark
Function
Please run the door-handing identifying process before function set up when first time installation or
default setting restore.
It should be remained
unlock while programming.
Up to 6 sets of User Code can be saved. User Code should be 4-10 digits in length.
Auto-locking and K eypad locking function will be invalid when User Codes are deleted.
The lock can only be operated by key during the time.
The preset delay-time is 30 seconds, you can change the time by following
instruction. Repeat the steps to cancel the Auto-locking function.
10-99 seconds delay -time available.
Repeat same steps to turn beeper On/Off .
LED illumination is still functioning when it's in mute. But there will be no any warning alarm.
Auto-locking and K eypad locking function will be invalid when User Codes are disabled. The lock can
only be operated by key during the time. Repeat the steps to enable the User Codes again.
Disposable code will be no longer valid once being used.
Press “R” button for over 5 seconds, the programming will complete after you hear 3 long beeps.
After restore, you need to run the door handing identifying process before other function setting.
Detect Left / Right
Hand Door Installation
Add New UC
Delete An Existing UC
Delete All UC At once
Change PC
Toggle Autolock
On/Off
Set Autolock Time
Delay
Toggle Mute On/Off
Enable/Disable All UC
Create a disposable
UC
Restore all preset lock
settings
Press “R”
Enter PC
Enter PC
Enter PC
Enter PC
Enter PC
Enter PC
Enter PC
Enter PC
Enter PC
Enter PC
Press 0
Press 1
Press 2
Press 3
Press 4
Press 5
Press 6
Press 7
Press 8
Press 9
Programming Code (PC)
User Code (UC)
Programming
Button
Programming
Button
Programming
Button
Programming
Button
Programming
Button
Programming
Button
Programming
Button
Programming
Button
Programming
Button
Programming
Button
Programming
Button
Programming
Button
Programming
Button
Programming
Button
Programming
Button
Programming
Button
Programming
Button
Programming
Button
Programming
Button
Programming
Button
Programming
Button
Programming
Button
Programming
Button
Programming
Button
Programming
Button
Enter new UC
Enter the UC you
want to delete
Enter New PC
Enter Seconds
(10~99)
Enter
new disposable
UC
S pe c ific a tion
/
F unc tion
¿
]
{
}
¡
«
»
‹
USER MANUAL
]
Programming Button
Programming Button is for entering codes, clearing errors and
setting function. It's also lock button.
{
Number Buttons
Input the pass codes, each pass code is 4-10 digits in length.
}
Cylinder
Retract / Extend the latch bolt by key from exterior .
¡
Washer
Prevent water permeating into lockset.
¿
Battery Lid
Slide the lid to change the batteries
or restore default setting.
«
Battery Holder
Four AA
（
1.5V
）
Alkaline batteries.
»
R Button (Reset)
Restore default setting.
‹
Turn-Piece
Retract/Extend the latch
bolt from interior .
1.Battery
Four AA
（
1.5V
）
Alkaline batteries.
2.Low Battery
2-1 The batteries should be changed immediately once you see
the LED flashes in red and hear constant beep sounds for
about 10 seconds when press programming button.
2-2 All settings are retained in the memory and will not be
affected even if the battery is completely dead.
2-3 The lock still can be operated by key even there is a power
outage.
3.LED Indicator
3-1 LED flashes green once when successful operation.
3-2 LED flashes green twice when successful programming.
3-3 LED flashes red 3 times when there is an operation error .
3-4 LED flashes red 5 times when codes input error , the operation
will stop for system protection (Refer to 17).
3-5 LED flashes orange 3 times when system has been restored
to default setting.
3-6 LED flashes orange slowly while in programming mode.
4.Audio Indicator
4-1 1 beep sound indicates a successful operation.
4-2 2 long beeps indicate a successful programming
4-3 3 beeps indicate an operation error .
4-4 3 long beeps indicate that system has been restored to
default setting.
4-5 5 beeps when codes input error , the operation will stop for
system protection. (Refer to 17)
4-6 10 rapid beeps indicate the power of battery is low .
5.Programming Code
5-1 The preset Programming Code is 0000. Please delete it and
create your personal code when first time operation.
5-2 Only one set of Programming Code for function setting.
5-3 Programming Code is only for function setting, you can't
unlock the door by pressing Programming Code.
5-4 Programming code is 4-10 digits in length.
5-5 Programming code can be changed anytime if needed.
6.User Code
6-1 The preset User Code is 1234. Please delete it and create
your personal code when first time operation.
6-2 Up to 6 sets of User codes can be saved.
6-3 User Code is only for activating the lock, without
programming function.
6-4 User Code is 4-10 digits in length.
6-5 User Code can be deleted or changed anytime if needed.
7.Delete Individual User Code
7-1 User Codes can be deleted individually . You can reset the
same number as code even it's deleted before.
7-2 Y ou should enter Programming code to delete individual
User code.
8.Delete All User Codes At Once
8-1 All the User Codes can be deleted at once. Y ou can still reset
the same numbers as codes even they're deleted before.
8-2 Auto-locking and K eypad locking function will be invalid
after deleting all User Codes and the lock can only be
operated by key . All the electrical functions will be restored
when recreate new User Codes.
8-3 Y ou need to enter Programming Code to delete all User
Codes.
9.Temporarily Disable All User Codes
9-1 Auto-locking and K eypad locking function will be invalid
when User Codes are temporarily disabled. The lock can only
be operated by key during the time.
9-2 Repeat the programming steps again to restore the User
Codes.
10.Create a Disposable User Code
10-1 Disposable User Code will be no longer valid once being used.
10-2 Y ou can reset same number as Disposal User Code.
10-3 Y ou need to enter Programming Code to create a
Disposable User Code.
11.Restore Preset F actory Code
11-1 Y ou can restore Preset F actory Code by pressing “R” button
on the interior receiver module when you forget Programming
Code or you want to cancel all previous setting.
11-2 After restore, the Programming Code would be 0000; the
User Code would be 1234 again.
12.Unlock the door
The door will be unlocked by key or pressing User Code on
keypad from outside or by interior turn-piece.
13.Lock the door
The door will be locked by key or pressing Programming Button
on keypad from outside or by interior turn-piece.
14.Incomplete Door Closing / Opening
14-1
Once the latch bolt is not extended/retracted completely
and causing a not functional motor operation when it's
locked by keypad, you'll see LED flash red 3 times (for twice)
and hear 3 beeps (No alarm when it's in mute). Y
ou need to
enter User Code to unlock the door for remaining the bolt
retracted, and press Programming Button to lock the door
again.
14-2 If the latch bolt gets stuck or can't extend/retract
completely all the time, please check if the strike aligns with
the latch bolt perfectly and adjust the strike to proper
position. After long use of the door hinge, the latch bolt
might get stuck easily because the door is deformed or
lopsided.
15.To Activate / Deactivate Auto-Locking F unction
15-1
The door will automatically lock itself within 10~99 seconds
when this function is programmed.
15-2
This function is not preset at the beginning; it can be set if
needed.
15-3
The preset delay-time is 30 seconds; you can adjust the
period you want.
15-4
Please repeat the same programming steps to cancel
Auto-Locking function when needed.
15-5
The system will alarm twice if
the latch bolt gets stuck
or not
extended/retracted completely.
You need to enter User Code to unlock the door for
remaining the bolt retracted. The auto-locking function will
be restored then.
16.Toggle Mute On/Off
16-1 Y ou will hear beep sounds when pressing keypad,
programming or operating errors. It can be turned off if
needed.
16-2 LED Illumination is still functioning when it's in mute. F or
there will be no any warning alarm, we suggest not to mute
the beeper if it's not necessary .
16-3 Motor operating sound cannot be muted.
17.Code Protection F unction
The operation will stop if entering unauthorized codes over 5
times. The System will re-operate again after 45 sec.
18.Illumination
The LED Keypad will light up when pressing any button for ease
of operating in the dark.
1. It should be remained unlock while programming.
2. Please run the door -handing identifying process
(Refer to programming table) before function set up when first
time installation or default setting restore.
3. Please change default Programming Code (0000) and User
Code (1234) before function set up when first time operation.
4. LED flashes orange slowly while programming. LED flashes
green twice with 2 long beeps when correct input. LED flashes
red 3 times with 3 beeps when incorrect input.
(Y ou need to wait for 6 seconds or press programming button
when incorrect input, then re-program the system again.)
5. Every programming step should be done in 6 seconds.
6. You can lock/unlock this product by either key or pass code.
Please refer to the following programming table for function
set up.
P ass Code & F
unction Set up
Remark
1. W e recommend to use alkaline battery in order to stabilize the
power supply .
2. Do not mix alkaline battery with regular zinc-carbon ones or
mixed brands.
3. Do not use any chemical liquid or lubricating oil with additives
to clean the lock body , it will damage the surface or even
mainboard.
4. If there is any problem of the product, please contact your
local retailer and send back the product to us for repair or
replacement.
Lockey Digital Systems Inc.
www.lockeyusa.com
