Lochinvar Knight LG30GCE Скачать руководство пользователя

Страница: 2 / 28

Read these installation instructions first before installing the appliance. Carefully read the

user instructions before igniting the appliance. Failure to follow these instructions may lead

to risk of explosion and/or fire and could cause material damage and/or bodily harm.

Installation and commissioning should be carried out by a qualified competent installer.

The type of gas and the value at which the appliance is set standard in the factory are

registered on the rating plate. The appliance may only be installed in a room if this room

meets the ventilation requirements.

lochinvar ltd. accepts no responsibility for warranty, service and/or product liabi-

lity in case of unauthorized alterations, product modifications or repair.

Содержание Knight LG30GCE





























Результаты поиска

Содержание Knight LG30GCE

Отзывы:

Похожие инструкции для Knight LG30GCE

Бренды по названию

Популярные бренды

Lochinvar Knight LG30GCE, Инструкция по установке, пусконаладке, эксплуатации и техническому обслуживанию

Результаты поиска

Содержание Knight LG30GCE

Отзывы:

Похожие инструкции для Knight LG30GCE

Бренды по названию

Популярные бренды