background image

 24 • Residen  al Standard Gas Water Heater Use and Care Guide

OPERA

TION

3

Allow the water heater’s main 
burner to operate for fi ve 
minutes. Pass a newly ex  n-

guished match approximately one inch 
from the dra   hood’s relief opening. 
Smoke from the match should be 
steadily drawn into the opening indicat-
ing the water heater is ge   ng adequate 
air and the vent system is working. 

Figure 35 - Test the air supply and vent to make 
sure the water heater has adequate air and is 
venting properly.

4

If the main burner has been 
opera  ng for fi ve minutes but 
the match smoke dri  s around 

or is blown away from the opening, turn 
the gas control knob OFF. Inspect the 
vent system and repair if necessary. In 
many cases, failure to pass the air 
supply and vent test indicates the water 
heater is not ge   ng enough air or there 
is a problem with the vent system. It 
may be necessary to increase the air 
supply by ge   ng air from outside (see 
page 7). 

WARNING! Burn Hazard. Do not 

touch the vent, doing so can cause 
burns. If the dra   hood does not draw 
in smoke from a match a  er fi ve 
minutes of main burner opera  on, 
shut the gas supply off , and do not 
operate the water heater un  l the vent 
system and air supply have been 
checked by a qualifi ed person and 
repaired if necessary. Con  nuing to 
operate the water heater in this 
condi  on could lead to serious injury 
or death from carbon monoxide 
poisoning. 

Temperature Control 
System

Adjus  ng the Temperature

With the installa  on steps completed, 
you may adjust the water heater’s tem-
perature se   ng if desired.

1

Set the gas valve to the desired 
temperature. The “HOT” 
se   ng sets the water tem-

perature to approximately 120°F, 
reducing the risk of scald injury. You 
may wish to set a higher temperature to 
provide hot water for automa  c 
dishwashers or laundry machines, to 
provide more hot water capacity, and to 
reduce bacterial growth. Higher tank 
temperatures (140° F) kill bacteria that 
cause a condi  on known as “smelly 
water” and can reduce the levels of 
bacteria that cause water-borne 
diseases.

Water usage pa  erns, as well as heat 
from sources such as solar collectors, 
ambient air, and the pilot light can 
result in temperatures higher than the 
thermostat set-point. 

WARNING! Higher temperatures 

increase the risk of scalding, but even at 
120°F, hot water can scald (see Table 1). 
Install Thermosta  c Mixing Valve(s) at 
each point-of-use to reduce the risk of 
scalding.

2

To adjust the water heater’s 
thermostat:

Figure 36 - Adjust the gas control knob to “HOT”. 

Turn the gas control knob on the gas 
control valve to the right to the follow-
ing se   ngs.  
• 

“A”    

128°F

• 

“B”   

138°F

• 

“C”   

147°F

• 

“VERY HOT”   160°F

NOTICE:  The temperatures above are 
approximates.  The actual temperature 
of the heated water may vary.

3

 Wait for the water to heat up. 
If you have no hot water a  er 
two hours, refer to the 

Troubleshoo  ng Sec  on (see page 25).

NOTICE

: If the tank is full of cold water, 

condensa  on may form inside the 
water heater. This condensa  on may 
drop on the burner causing a sizzling 
sound. In some cases, you may see a 
small puddle on the fl oor. Condensa-

 on is normal and should go away once 

the tank reaches its normal opera  ng 
procedure.  

WARNING! If you have increased 

the temperature se   ng and the 
Thermosta  c Mixing Valves are not set 
properly (or not installed) you could 
scald yourself while checking the 
temperature.

4

Check water temperature at 
several points of use in your 
home (for example, bathtub 

faucet, shower, or lavatory sink) and 
adjust the Thermosta  c Mixing Valves 
as needed. If you aren’t sure how to 
adjust the Thermosta  c Mixing Valve 
se   ngs, or aren’t sure if you have 
Thermosta  c Mixing Valves, contact a 
qualifi ed person.

Opera  ng Modes

The gas control valve has two diff er-
ent opera  ng modes: Standard and 
Vaca  on. The Standard mode allows 
you to adjust the water temperature 
to your desired se   ng. The Vaca  on 
(VAC) mode sets the thermostat at 
approximately 55°F  and is recom-
mended when not using hot water for 
an extended period of   me. The VAC 
se   ng also reduces energy losses and 

 24 • Residen  al Standard Gas Water Heater Use and Care Guide

OPERATION

Содержание GSL050-40





































Отзывы: