LNR Mountain Topper MTR-5B Скачать руководство пользователя страница 1

Страница: 1 / 26

The MTR-5B

Five band Mountain topper

KD1JV Designs

[email protected]

revised 12-12-15

(shown with optional enclosure sold by LnR Precision, production kits use white backlight display)

Features:

Switch selected 40/30/20/17/15 meter bands

(no band modules to lose or change out)

Wide operating voltage range, 6 to 12 volts

15 ma Rx current at 12V supply

Efficient transmitter. Low current with 4W output

LCD display

Push button or Optional rotary tuning

24 hour clock built in, with battery back up

Three 63 character programmable message memories

Message beacon mode with adjustable pause time

Small size: can fit into a 4” x 3” x 3/4” box

MTR-5B Page -1-

Five Band Mountain Topper - KD1JV Designs

Manufactured by LNR Precision, Inc. www.LNRprecision.com

Manual Revision 12-12-15

Содержание Mountain Topper MTR-5B



























Результаты поиска

Содержание Mountain Topper MTR-5B

Отзывы:

Похожие инструкции для Mountain Topper MTR-5B

Бренды по названию

Популярные бренды

LNR Mountain Topper MTR-5B, Руководство пользователя

Результаты поиска

Содержание Mountain Topper MTR-5B

Отзывы:

Похожие инструкции для Mountain Topper MTR-5B

Бренды по названию

Популярные бренды