LIW LORI Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 21

LIW LORI Скачать руководство пользователя страница 18

page 18

LORI Stander edition 2

Shoulder protectors

–

Figure 23

In the case of rear verticalisation, shoulder support is sometimes required for the safety and comfort of the user.
The Lori stander offers an accessory that makes this possible. To adjust the front angle, loosen the knobs (4), then set the

required angle and tighten the knobs when the adjustment is complete. To change the depth and tilt in the upper plane, loosen
the screws (3). After adjusting the angle and depth, tighten the screws (3).

Figure 23

Fastened SideUP chest supports

–

Figure 24

To release the support, press the red button of the buckle (see ), then lift the support (1) and tilt it. Proceed with the second

support in the same way. The tilted supports make it easier to place the patient in the device. To re-fasten the SideUP supports, tilt
them back until they snap back into their base position.
The SideUP supports can be adjusted in two directions by loosening the knob (2) and tightening the knobs (2) after adjustment (2)

Figure 24

«
...
16
17
18
19
20
...
»

Содержание LORI






















Отзывы:

Нет отзывов