L
ittfinski
D
aten
T
echnik
(
LDT
)
Assembly Instruction
16-fold feedback module
from the
Digital-Professional-Series
!
RS-16-O-B
Part-No.:
310201
>> kit <<
As
LR101
but with 16 inputs and additional optocoupling
for potential separation and for high interference safety.
Suitable for the RS-feedback bus
⇒
controls up to 16 feedback contacts
(safe galvanic separation by opto coupler).
⇒
separated by opto coupler
(contacts can be separated from layout ground
connection).
⇒
compatible to RS-feedback bus
(can be operated together with RS-8, LR101, LS100
etc.).
⇒
suitable for Lenz Digital plus System.
This product is not a toy! Not suitable for children under 14 years of age! The kit
contains small parts, which should be kept away from children under 3! Improper
use will imply danger of injuring due to sharp edges and tips! Please store this
instruction carefully.
Introduction:
You have purchased the 16 fold feedback module
RS-16-O
with
galvanic separation by opto coupler for your model railway. The
RS-16-O
is a high quality product that is supplied within the
Digital-Professional-Series
of
L
ittfinski
D
aten
T
echnik (
LDT
).
We wish you having a good time using this product.
The feedback module
RS-16-O
can be easily operated on the
RS-feedback bus of your digital model rail way.
The
RS-16-O
is compatible to all digital model railways with RS-
feedback bus (e.g.
Digital Plus
from Lenz).
General:
Tools required for the assembly
Please assure that the following tools are available:
•
a small side cutter
•
a mini soldering iron with a small tip
•
solder tin (if possible 0.5mm diameter)
Safety Instructions
•
All electrical and electronic components included in this kit
shall be used on low voltage only by using a tested and
approved voltage transducer (transformer). All components
are sensitive to heat. During soldering the heat shall be applied
for a very short period only.
•
The soldering iron develops a heat up to 400°C. Please keep
continual attention to this tool. Keep sufficient distance to
combustible material. Use a heat resistant pad for this work.
•
This kit consist of small parts which can possibly be swallowed
from children. Children (especially under 3 years) shall not
participate on the assembly without supervision.
Set-Up:
For the board assembly please follow exact the sequence of the
below
assembly list
. Cross each line off as
done
after
completing the insertion and the soldering of the respective part.
For the
diodes
please keep special attention to the correct
polarity (marked line for the cathode).
With reason to different makes of
electrolytic capacitors
you
will find different markings of the polarity. Some are marked with
"+" and some are marked with "-". Each capacitor has to be
assembled to the board that the marking on the capacitor is in
correspondence with the marking on the pc-board.
Integrated circuits (IC`s)
are either marked with a half round
notch on one end or a printed point for the correct mounting
position. Push the IC`s into the correct socket or directly into the
pc-board (
IC11
) assuring that the notch or the printed point is
corresponding to the half-rounded marking on the pc-board.
Please attend to the sensitivity of the ICs to
electrostatic
discharge,
which will cause immediate damage of the IC. Before
touching those components please discharge yourself by
contacting an earthed metal (e.g. earthed radiator) or work with
an electrostatic safety pad.
Attend to the flat side of the
transistors
.
Resistor networks
are marked at the one side with a printed
circle or a square for Pin 1.
Before assembling the unit clip the
clamps
together to a block
with the required
connections
.
The
light emitting diodes
have to be assembled with the longer
leg to be connected to "+" on the pc-board. Before soldering the
diodes push the
distance
spacer tubes
on to the legs.
Assembly list
Pos. Qty. Component
Remarks
Ref.
Done
1
1 Pc-board
2
2 Resistors 1,5KOhm
brown-green-black-brown
R1, R2
3
1 Resistor 220KOhm
red-red-black-orange
R3
4
2 Resistors 2,2KOhm
red-red-black-brown
R4, R9
5
1 Resistor 220Ohm
red-red-black-black
R5
6
1 Resistor 120Ohm
brown-red-black-black
R6
7
1 Resistor 33Ohm
orange-orange-black-gold
R7
8
2 Resistors 22KOhm
red-red-black-red
R8, R10
9
1 Resistor 3,3KOhm
orange-orange-black-brown
R11
10
1 Resistor 1MOhm
brown-black-black-yellow
R12
11
4 Networks 4*10kOhm
attend to the polarity!
RN1 ... 4
12
2 Networks 8*10kOhm
attend to the polarity!
RN5 ... 6
13
2 Diodes 1N4148
attend to the polarity!
D1, D5
14
1 Diode 1N4003
attend to the polarity!
D2
15
2 Diodes BZX83 5V6
attend to the polarity!
D3, D4
16
4 Capacitors 100nF
100nF = 104
C19...22
17
1 IC: LTV817
attend to the polarity!
IC11
18
1 IC-socket 18poles
IC1
19
2 IC-sockets 16poles
IC2, IC3
20
4 IC-sockets 16poles
IC5 ... 8
21
1 IC-socket 8poles
IC4
22
2 IC-sockets 6poles
IC9, 10
23
1 Resonator 8MHz
CR1
24
1 Electrolytic capacitor 100uF/25V
attend to the polarity!
C18
25
1 Electrolytic capacitor 220uF/35V
attend to the polarity!
C17
26
1 Push button
S1
27
4 Transistors BC 547
attend to the polarity!
T1 ... T4
28
1 LED plus spacers
attend to the polarity!
LED1
29
4 Clamps 2poles
build blocks before assembly
30
5 Clamps 3poles
build blocks before assembly
31
1 IC: Z86E0812PSC
attend to the polarity!
IC1
32
2 IC: 4014
attend to the polarity!
IC2, 3
33
1 IC: 93C46
attend to the polarity!
IC4
34
4 IC:LTV844
attend to the polarity!
IC5 ... 8
35
2 IC:CNY17III
attend to the polarity!
IC9, 10
36
final control
Made in Europe by
L
ittfinski
D
aten
T
echnik (
LDT
)
Bühler electronic GmbH
Ulmenstraße 43
15370 Fredersdorf / Germany
Phone: +49 (0) 33439 / 867-0
Internet: www.
ldt-infocenter
.com
Subject to technical changes and errors.
07/2019 by LDT
