L
ittfinski
D
aten
T
echnik (
LDT
)
Assembly Instruction
Multi-Digital
s88-N
16-fold Feedback Module
for the s88-Feedback bus
from the
Digital-Professional-Series
!
RM-88-N-B
Part-No.:
310111
As Märklin s88 with 16 inputs.
>> kit <<
Suitable for digital control devices and interfaces
with s88-feedback bus:
⇒
with 16 input connections, switching against
ground
(e.g. for contact tracks [one isolated rail], switch
tracks or reed-contacts).
⇒
for s88-standard connections and s88-N
(with 6-poles s88-pinbars and RJ-45 sockets).
⇒
suitable for the digital control:
Märklin-Digital~/=, Central Station 1 and 2, Intellibox, TWIN-
CENTER, HIS-88(-USB), EasyControl, ECoS, DiCoStation.
This product is not a toy! Not suitable for children under 14 years of age! The kit
contains small parts, which should be kept away from children under 3! Improper
use will imply danger or injuring due to sharp edges and tips! Please store this
instruction carefully.
CE Part-No.:
24 80 31
Introduction:
You have purchased the 16-fold Feedback Module
RM-88-N
as
a kit for your model railway. The
RM-88-N
is a high quality
product that is supplied within the assortment of
L
ittfinski
D
aten
T
echnik (
LDT
).
The Feedback Module
RM-88-N
from the
Digital-Professional-
Series
can
operate on your digital control without any problems.
The
RM-88-N
is suitable for the application on any digital control
unit which supports the
s88 feedback bus
We are wishing that you will have a good time for assembling and
using this product.
General:
Tools required for the assembly
Please assure that the following tools are available:
•
a small side cutter
•
a mini soldering iron with a small tip
•
solder tin (if possible 0.5mm diameter)
Safety Instructions
•
All electrical and electronic components included in this kit
shall be used on low voltage only by using a tested and
approved voltage transducer (transformer). All components
are sensitive to heat. During soldering the heat shall be applied
to the respective component for a very short period only.
•
The soldering iron develops up to 400°C. Please keep
continual attention to this tool. Keep sufficient distance to
combustible material. Use a heat resistant pad for this work.
•
This kit consist of small parts, which can be possibly swallowed
from children. Children (especially under 3 years) shall not
participate on the assembly without supervision.
Set-Up:
For the board assembly please follow exact the sequence of the
below
assembly list
. Cross each line off as
done
after
completing the insertion and the soldering of the respective part.
Please put the
clamps
together to a block with 17 connections
before assembling the clamps to the board.
Special attention is required for the
tantalum capacitor
. The leg
with the mark "+" has to be inserted to the respective marked
position on the pc-board.
Resistor-networks
are marked on one end with a printed circle
or a square. Assemble this component that way that the marking
corresponds with the marking between the first and second bore
on the pc-board. The first bore has been additionally marked with
a "1".
Please attend to the flat side of the
transistor.
Integrated circuits (IC`s)
are either marked with a half round
notch on one end or a printed point for the correct mounting
position. Push the IC`s into the correct socket assuring that the
notch or the printed point is corresponding to the half-rounded
marking on the pc-board.
Please attend to the sensitivity of the
ICs
to
electrostatic
discharge
, which will cause immediate damage of the IC. Before
touching those components please discharge yourself by
contacting an earthed metal (e.g. earthed radiator) or work with
an electrostatic safety pad.
Please
glue the two
labels
onto the
RJ-45 sockets
for
identification of the output socket
BU1
(cable in direction to the
central unit) and
BU2
(cable from next feedback unit).
s8
8
-N
O
U
T
IN
s8
8
-N
Label for BU1
Label for BU2
Assembly List:
Pos.
Qty. Component
Remarks
Ref.
Done
1
1
Printed Circuit Board
2
6
IC-Sockets 16poles
IC1..6
3
4
Networks 4*10kOhm
Attend to the polarity!
R1..R4
4
2
Networks 8*100kOhm
Attend to the polarity!
R5, R6
5
2
Resistors 100kOhm
brown-black-black-orange
R7, R8
6
1
Resistor 10kOhm
brown-black-black-red
R9
7
16
Capacitors 10nF
C1..C16
8
1
Tantalum cap. 1uF/35V
Attend to the polarity!
C17
9
1
Capacitor 100nF
C18
10
2
Pin-plugs 6poles
ST1, ST2
11
1
Transistor BC 547
Attend to the polarity!
T1
12
5
Clamps 3poles
Build a block before assy.!
KL1..KL5
13
1
Clamp 2poles
Build a block with KL1 to 5
KL6
14
2
RJ45 sockets
BU1, BU2
15
4
IC: 4044
Attend to the polarity!
IC1,2,4,5
16
2
IC: 4014
Attend to the polarity!
IC3, IC6
17
Final Control
Made in Europe by
L
ittfinski
D
aten
T
echnik (
LDT
)
Bühler electronic GmbH
Ulmenstraße 43
15370 Fredersdorf / Germany
Phone: +49 (0) 33439 / 867-0
Internet: www.
ldt-infocenter
.com
Subject to technical changes and errors.
06/2019 by LDT
Märklin is a registered trade mark.
