manualshive.com logo in svg

Lithium Grim OmniMuff, Инструкция по сборке

Поделиться
Скачать
Lithium Grim OmniMuff Скачать руководство пользователя страница 8

OmniMuff v1.0 

 

Manufacturers and product names are mentioned solely for circuit identification, and where applicable their trademarks are the 

property of their respective owners who are in no way associated or affiliated with the author. No cooperation or endorsement 
is implied.

 

8 

Off board wiring 

 

C

at

hode

 (

shor

t 

le

g)

An

od

e

 (l

on

g 

le

g)

Tip

Sleeve

Ring

Sleeve

Tip

R Led

Input Jack

Output Jack

 

Note that 

R led 

is a 

3k3/4k7

 resistors. You can change this value depending on the type of LED you 

use but 3k3 is safe enough for almost all LEDs @ 9V.  

The sleeve on the output jack is not connected on purpose. Make sure the output jack is in good 
electronic contact with the enclosure else you can try and connect the sleeves of the input and 
output together. If you test the unit outside of an enclosure you need to connect the output sleeve 
to ground! 

Note that there are two +9V pads on the board. 

You may only use 1 (!!)

 at a time else you might 

short circuit the board. In the picture above I used the bottom one, but if you are using a top 
mounted DC jack, it might be more convenient for you to use the top one on the PCB. 

It is now time to place your transistors in the sockets if needed. Connect everything, build it in your 
enclosure and enjoy your effect! 

 

Содержание OmniMuff











Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды