Fig. 4
Fig. 1
19˚
20˚
and
Above
RECEIVER
HANGING
BRACKET
DOWNROD
CAUTION:
FOR MOUNTING RECEIVER,CEILING
ANGLE SHALL NOT EXCEED 19 DEGREES
RECEIVER MODEL: CFR-3D
LITEX INDUSTRIES, LTD.
GRAND PRAIRIE, TX 75050
FOR CUSTOMER SERVICE CALL: 1-800-527-1292
Fig. 3
AC SUPPLY
BLACK
WHITE
BARE
GREEN
BLACK
WHITE
BLUE
BLUE
BLACK
WHITE
ANTENNA
Fig. 2
RECEIVER
CAUTION:
DO NOT USE
FAN SPEED CONTROL
IN CANOPIES WHERE
THE MOUNTING IS NOT
AS SHOWN IN FIGURE 2
OF THE INSTALLATION
INSTRUCTIONS
GENERAL INFORMATION
This remote control is designed to separately control your ceiling fan speed and light brightness.
There are four buttons to control the fan speed. The light dimmer button controls the light.
The red indicator on the transmitter will light when any button is pressed.
INSTALLATION AND OPERATING INSTRUCTIONS
I. SAFETY PRECAUTIONS
A.
DANGER: HIGH VOLTAGE!
Household electrical power can cause serious injury or death. Disconnect source of electrical
power to the ceiling fan by removing fuse or switching off circuit breaker. Make sure all electrical connections comply with local codes,
ordinances, the National Electrical Code, and ANSI/NFPA 70-1999. If you are unfamiliar with electrical wiring, please use a qualified
and licensed electrician.
B.
WARNING:
To reduce the risk of fire, electrical shock, or personal injury, wire connectors provided with the remote control
receiver are designed to accept only one 12 gauge house wire and no more than two lead wires from the receiver. If your
house wire is larger than 12 gauge or there is more than one house wire to connect to the two receiver wires, consult an
electrician for the proper size wire connectors to use.
C.
CAUTION:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT USE THE FAN
WITH ANY SOLID STATE SPEED CONTROL DEVICE OR CONTROL FAN SPEED WITH A FULL
RANGE DIMMER SWITCH.
D.
Do
not
use this remote control with solid state ceiling fans.
Electrical source and fan must be 115/120 volts, 60 Hz.
Maximum fan motor amps: 1.25; Maximum light watts: 300 incandescent only.
II. INSTALLATION OF RECEIVER (Please refer to Figure 1 before continuing.)
A.
Manually set fan speed control to HIGH via pull chain and set light to ON via pull chain.
IMPORTANT:
Fan speed and light control will not be activated by remote if pull chains for fan and light
are not set to the HIGH and ON positions, respectively.
B.
Disconnect source of electrical power to the ceiling fan by removing fuse or
switching off circuit breaker.
C.
Lower ceiling fan canopy from the hanging bracket.
D.
Disconnect existing wiring between ceiling fan and supply at electrical outlet box.
E.
Lay the black antenna wire on top of the receiver and slide the
receiver into the hanging bracket. (Figure 2)
F.
Using the wire connectors supplied, make wiring connections as follows: (Figure 3)
CONNECT:
TO:
GREEN
fan wire......................................................
BARE
supply wire
BLACK
receiver wire (AC IN L)...............................
BLACK
supply wire
WHITE
receiver wire (AC IN N)...............................
WHITE
supply wire
WHITE
receiver wire (TO MOTOR N)......................
WHITE
fan wire
BLACK
receiver wire (TO MOTOR L)......................
BLACK
fan wire
BLUE
receiver wire (FOR LIGHT)............................
BLUE
light wire (from fan)
Wrap each wire connector separately with electrical tape as an extra safety measure.
If other fan or supply wires are different colors than those
mentioned, have this unit installed by a qualified electrician.
G.
Push all connected wires up into outlet box. Make sure antenna rests
outside
of
hanging
bracket.
H.
Re-install the canopy on the hanging bracket.
III. AUTOMATED LEARNING PROCESS/ACTIVATING CODE
A.
Remove battery cover.
B.
Install the two AAA batteries (included).
C.
Restore electrical power. Within 30 seconds of restoring electrical power, press the “LEARN” button, located in battery compartment,
for 3 seconds or until fan switches to MEDIUM speed. Test the light and fan functions to confirm the learning process is complete. (Figure 4)
CAUTION:
The transmitter can be programmed to multiple receivers or fans. If this is
not
desired, turn power off to any other programmable
receiver or fan.
D.
Locate dimmer switch next to the “LEARN” button in battery compartment. (Figure 4) Set dimmer switch to ON position only if using
incandescent bulbs. Set dimmer switch to OFF position if using compact fluorescent bulbs.
NOTE
: Compact fluorescent bulbs are
NOT
compatible for use with dimmer controls.
E.
Replace battery cover on transmitter.
(Figure 4)
IV. TRANSMITTER--CARE
AND
OPERATION
A.
Store the transmitter away from excess heat or humidity.
B.
To prevent damage to transmitter, remove the battery if not used for long periods.
C.
Operation buttons on the front panel of the transmitter:
HI button
for fan HIGH speed
MED button
for fan MEDIUM speed
LOW button
for fan LOW speed
OFF button
for fan speed OFF
button
for light BRIGHTNESS and OFF
The light function is controlled by pressing the button. Hold button down to increase or
decrease light. Tap button quickly to turn light off or on. If you press the button in excess of
0.7 second it becomes a dimmer. The light varies cyclically in 0.8 seconds. The light button
has auto resume, so the light will stay at the same brightness as the last time it was turned off.
IMPORTANT:
Make sure that fan has been turned off at wall switch and then allow blades to
come to a complete stop before
manually
activating the reverse switch on the fan.
V. TROUBLESHOOTING GUIDE
A.
Fails to operate:
1.
Power to the receiver?
2.
Receiver wired correctly?
3.
Manual speed control on fan in highest position?
4.
Light kit switch turned on?
5.
Good batteries in the transmitter?
6.
Learning process between fan and transmitter may not have been successful.
Turn power off, remove battery cover and repeat Steps C and E in Part III
(Automated Learning Process) above.
B.
Won't operate at distance: If transmitter operates fan and light kit when up close, but not at 40 feet
away, try placing the black antenna wire higher and make sure the black antenna wire is visible.
MODEL: RCI-103
AC SUPPLY
BLACK
WHITE
CAUTION:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
USE THE FAN WITH ANY SOLID STATE SPEED CONTROL DEVICE
OR CONTROL FAN SPEED WITH A FULL RANGE DIMMER SWITCH.
TRANSMITTER
(front)
(back)
LEARN
BUTTON
DIMMER
SWITCH
AAA
AAA