IMPORTANT:
Review this installation guide in its entirety before starting installation of
your Smart Dimmer Switch or removal of your old switches. Installation and maintenance
involving electrical wiring must be done by qualifi ed person(s). Risk of Electric Shock:
Electricity can cause personal injury and property damage if handled improperly. An
external air gap switch shall be installed before circuit connection to this device. The
metal heatsink plate is not grounding, which might become live. Install with plastic Cover
Plate only.
Wireless Frequency:
2.4GHz, 802.11b/g
Input: 120VAC,
60Hz
Output Power (120VAC): LED/Fluorescent: 150W Max
Incandescent: 400W Max
Output Current:
3.3A
Standby Power:
0.5W
Enclosure Type:
Type 1 Enclosure (after installation)
Action type:
Type 1.Y action
Caution:
To reduce the risk of injury and/or overheating and damage to other equipment:
• Make sure that the power at the circuit breaker is turned OFF before starting.
• A neutral (typically white) wire is required.
• Replace single pole switches ONLY. Not compatible with 3-way switches.
• The wire colors indicated in this manual are typically found and may differ in some
constructions / regions.
• Ensure the wire conductors are securely fastened to each wire.
• It is recommended that a certifi ed electrician completes all high voltage electrical
installations.
• Must follow all building and electrical codes in the region when installing.
• Do not install to control an appliance, motor or receptacle.
• Recommended to be installed in a minimum 2.5" depth device box.
• Do not mix different load types or different luminaires on the same dimmer.
• Dimmer does not work with smart bulbs or fi xtures.
• Intended for installation in an in-wall electrical box.
1. Turn OFF the power at the
circuit breaker and confi rm
with the voltage tester at the
switch before proceeding.
Place voltage tester against the
existing switch checking the
wall plate, screws and switch
at various points to determine
that there is no power present.
NOTE: INSTALLATION OF THIS SMART DIMMER REQUIRES
A NEUTRAL WIRE. IF NEUTRAL WIRE IS NOT CONNECTED,
THIS DIMMER WILL NOT WORK. CONSULT A QUALIFIED
ELECTRICIAN.
MODEL: LC-CRTL-DIM-1
Wi-Fi Smart Control with Dimmer
User Manual
LITELINE CORPORATION
Telephone 1.866.730.7704 | Fax 1.888.738.9736 liteline.com
UM_LC-CRTL-DIM-1_9.16.20
Before you start
Specifi cations
What you need
Product overview
Installation
Brightness
Indicator
Lights
Power/Connectivity Indicator Light
ON/OFF
Switch
Touch
Dimming
Area
Screwdrivers
Pliers
Wire Stripper
Voltage Tester
2. Remove the wall plate and pull
out the existing light switch
so that all wires are exposed
outside of the gang box (do not
disconnect wires).
3. Label the live wire with a piece
of electrical tape.
4. Disconnect and remove the
existing switch.
5. Connect the Smart Dimmer as
per the below wiring diagram.
The ground wires must be
connected to the electrical box.
6. Mount the Smart Dimmer in the existing gang box with the
provided screws and attach the wall plate (press fi t).
Neutral
(Required)
Live (Required)
Load
Ground
7. Turn on the power at the circuit breaker.
8. Test to see that the Smart Dimmer is functioning by pressing
the ON/OFF switch. Your load (lights) should turn ON/OFF
respectively.
Note:
If your lights do not turn on, your live and load wires
might be incorrectly connected. Turn off power at the circuit
breaker and try swapping them.
9. WiZ app setup
Refer to “WiZ Quick Setup Guide”
OFF
ON
OFF
ON
OFF
ON
OFF
ON
WiZ Quick Setup Guide
Downloading the WiZ App
Before you start, make sure you install the WiZ App from
either
Google Play
or the
Apple App Store
(both offer
the same set of features). The app can also scale to fi t
tablets as needed.
Note:
Upon fi rst boot-up, the fi rmware may need to be updated. Please allow up to 1 minute for the Smart Dimmer to update after completing WiZ app setup.
For additional support, visit www.liteline.com/WiZsupport
Installing and pairing smart dimmer
The dimmer switch is connected through the app and will only operate on your home’s 2.4GHz Wi-Fi network. Most
new routers are dual-bandwidth (both 2.4GHz and 5GHz), ensure you select the 2.4GHz network which covers a
wider range than the 5GHz. To make sure your phone is on the 2.4GHz network, either select it in the list of available
networks on your phone or go into the router settings and temporarily de-activate the 5GHz network (you can activate
it again after pairing is done).
If this is not possible and the dimmer switch is not found, try putting the dimmer switch in pairing mode by holding the
ON/OFF button for 5 seconds (or until the indicator lights fl ashes red), then walking a short distance away from the
router. Due to the short range of 5GHz networks, your phone should auto-connect to the 2.4GHz at this point. Once
connected, you can start pairing in the app. You can pair as many devices as you want at the same time.
Create a home or join an
existing one
Name your home
Tap the ‘Add room’ button
to add a room
Name your own or select
from the list of standard
rooms
Press the ‘Add a device’
button and enter your
Wi-Fi password
Select the ‘Wi-Fi Switch’
and continue with prompts
to connect your device
INDICATOR LIGHTS STATUS
ON/OFF SWITCH FUNCTION
Dimmer functions
Troubleshooting
LIGHTS
INDICATOR LIGHT
STATUS
COLOR
STATUS
Power /
Connectivity
Indicator
Light
ON
WHITE
Powered OFF
OFF
Powered ON
Single Blink
Ready for Smart
Pairing
mode
Double Blink
Ready for Manual
Pairing
mode
Flashing Quickly
RED
Pairing failed
Brightness
Indicator
Lights
7 LEDs Flashing,
Power/Wi-Fi Indicator
Light is OFF
WHITE
Operating temperature is too high;
switch has been turned off
0%~14% Brightness Level
14%~28% Brightness Level
28%~42% Brightness Level
42%~56% Brightness Level
56%~70% Brightness Level
70%~84% Brightness Level
84%~100% Brightness Level
ACTION
COLOR
STATUS
Short Press
OFF
Dimmer is ON
Short Press
White
Dimmer is OFF
Long Press (5 seconds)
White LED Double
Blink
Connectivity Mode: Wi-Fi network is
acquired
PROBLEM
CAUSE
SOLUTION
Unable to fi nd the
Smart Dimmer on
the network
Smart Dimmer
may not be in
Connectivity Mode
Long Press the ON/OFF switch (5 seconds)
to enter into Connectivity Mode: Searching
for Wi-Fi Network.
Unable to operate
the load (light) with
the ON/OFF switch
Wiring issue
Review and confi rm the INSTALLATION
section in this manual.
No electricity
Check that the power is ON at the circuit
breaker.
Load does not
function or is
incompatible
• Replace the load.
• Check the SPECIFICATION section for
compatible loads and limitations.
Smart Dimmer not
responding to WiZ
APP control
Network is not
connected
Check wireless network connectivity.
Permissions are not
granted on mobile
device
Check to see that permissions are granted
for the WiZ APP.
Smart Dimmer is not
functioning correctly
Manually press the ON/OFF switch to see
electrical functionality is working.
Load (light) not
functioning properly
Load (light) may not
be compatible or
exceeding limits
• Check SPECIFICATION section to ensure
load (light) is within limits.
• Replace the load (light).
Smart Dimmer not
connecting to the
WiZ APP
Wi-Fi password is
incorrect
Re-enter Wi-Fi password.
Weak/low Wi-Fi
signal
Check Wi-Fi signal to ensure within range
of router.
Wi-Fi not connected Confi rm Wi-Fi router is broadcasting a
2.4GHz signal. Re-connect.
WiFi
®
is a registered trademark of Wi-Fi Alliance
®
. Google Play and the Google
Play logo are trademarks of Google LLC. App Store is a service mark of Apple Inc.,
registered in the U.S. and other countries. Other trademarks and trade names are
those of their respective owners.
The following importer is the responsible party:
LLC Sales, Inc. DBA Liteline USA
1209 Orange Street, Wilmington, DE, 19801
liteline.com/page/contact-us
Changes or modifi cations not expressly approved by the responsible party could void
the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures: (1) reorient or
relocate the receiving antenna; (2) increase the separation between the equipment
and receiver; (3) connect the equipment into an outlet on a circuit different from that
to which the receiver is connected; (4) consult the dealer or an experienced radio/TV
technician for help.
RF Exposure Requirements:
This device complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. The antenna(s) used for this transmitter must not be co-
located or operating in conjunction with any other antenna or transmitter and must be
installed to provide a separation distance of an least 20cm from all person.
ISED Canada Statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply with
Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).
Operation is subject to the following two conditions: (1) this device may not cause
interference; and (2) this device must accept any interference, including interference
that may cause undesired operation of the device.
Limited 1-Year Warranty
For complete warranty information, including details on consumer legal rights as well
as warranty exclusions, visit www.liteline.com/warranty.
Piece of
electrical tape
Different color screw
(Black or Copper)
OFF
ON
OFF
ON
OFF
ON
OFF
ON
QR CODE
Direct to
Apple app store / Google play store
Copyright © 2020, Liteline Corporation. All rights reserved.
LC-CRTL-DIM-1_instructions.indd 1
LC-CRTL-DIM-1_instructions.indd 1
16/09/2020 3:22:50 PM
16/09/2020 3:22:50 PM
