background image

FEDERAL COMMUNICATIONS COMMISSION 

This device complies with Part 15 of the FCC Rules. Operation is subject to the 

following two conditions:(1) this device may not cause harmful interference, and (2) 

this device must accept any interference received, including interference that may 

cause undesired operation. 

Changes or modifications not expressly approved by the party responsible for 

compliance could void the user‘s authority to operate the equipment. 

NOTE 

This equipment has been tested and found to comply with the limits for a Class B 

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to 

provide reasonable protection against harmful interference in a residential installation. 

This equipment generates, uses and can radiated radio frequency energy and, if not 

installed and used in accordance with the instructions, may cause harmful interference 

to radio communications. However, there is no guarantee that interference will not 

occur in a particular installation If this equipment does cause harmful interference to 

radio or television reception, which can be determined by turning the equipment off 

and on, the user is encouraged to try to correct the interference by one or more of the 

following measures: 

 

-Reorient or relocate the receiving antenna. 

-Increase the separation between the equipment and receiver. 

-Connect the equipment into an outlet on a circuit different from that to which the 

receiver is connected. 

-Consult the dealer or an experienced radio/TV technician for help. 

 

Note: 

This device and its antenna(s) used for this transmitter must not be co-located or 

operating in conjunction with any other antenna or transmitter.

 

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled

 environment. In order to avoid the possibility of exceeding the FCC radio frequency

 exposure  limits, human proximity to the antenna shall not be less than 20cm (8 inches)

 during normal operation.

 

Содержание WP310A










Отзывы: