Lissmac UNICUT 520 Скачать руководство пользователя страница 39

Страница: 39 / 92

39/92

TRANSPORT

6.1.

Transport position

Conditions



Engine is turned off.



Saw blade guard is dismantled.



Saw blade is removed.



Seat with water pump and footboard removed.



Cable and hoses are lashed or separated.

WARNING

Injuries due to slipping or tilting of the machine

Unintentional changes in the position of the machine can crush people.



Only transport the floor saw in transport position.



Secure the floor saw over the attachment points.



Use suitable lifting and lashing straps.

NOTICE

Machine transport

When transporting the floor saw, unintentional changes in position must be avoided. Engine oil can run
into the combustion chamber of the engine and damage the engine.

Maximum inclination on all sides 30°.

All moving parts that could fall off, swing or disturb during transport must be removed!

NOTICE

Driving on ramps

When driving the floor saw over ramps, the blade guard can be moved to a raised position to avoid
collision.

Lifting the blade guard
for driving over ramps



Remove saw blade (see 4.5).



Move blade guard all the way up.



Move the saw head all the way down.



Insert safety bolt.



Continue to lift the blade guard by lifting the saw head.

Содержание UNICUT 520





























































































Результаты поиска

Содержание UNICUT 520

Отзывы:

Похожие инструкции для UNICUT 520

Бренды по названию

Популярные бренды

Lissmac UNICUT 520, Руководство по эксплуатации

Результаты поиска

Содержание UNICUT 520

Отзывы:

Похожие инструкции для UNICUT 520

Бренды по названию

Популярные бренды