Lissmac MULTICUT 550 GH Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 92

background image

33/92

5.

TRANSPORT

5.1.

Transport position

WARNING

Crush hazard from unsecured machine

Injuries through unintentional position change of the machine or falling of parts.



Only transport the floor saws in the transport position



Secure the floor saw via the attachment point

NOTICE

Transport of the machine

Large inclined positions must be avoided during the transport of the floor saw.
Fuel can spill or engine oil can enter the combustion chamber of the motor and damage the motor.

Maximum inclination in all directions 30°. Only transport in an upright position.
All movable parts, which could fall, swing during transport must be removed.

Transport position

•

Stop engine

•

Activate parking lock

•

Remove blade guard

•

Remove saw blade

•

Fold up and secure steering rod with rope

•

Remove handle bars

•

Remove or secure any loose parts

«
...
31
32
33
34
35
...
»

Содержание MULTICUT 550 GH





























































































Отзывы:

Нет отзывов

Похожие инструкции для MULTICUT 550 GH

Бренд: Target Страницы: 36

Бренд: Gröne Страницы: 160

Бренд: baalbaki Страницы: 2

Бренд: DeWalt Страницы: 40

Бренд: Clarke Страницы: 16

Бренд: Clarke Страницы: 16

Бренд: Clarke Страницы: 16

Бренд: Clarke Страницы: 28

Бренд: Wolf Creek Страницы: 14

Бренд: Meec tools Страницы: 15

Бренд: Meec tools Страницы: 29

Бренд: Meec tools Страницы: 32

Бренд: Meec tools Страницы: 47

Бренд: Meec tools Страницы: 50

Бренд: Meec tools Страницы: 103

Бренд: Worx Страницы: 184

Бренд: FOM INDUSTRIE Страницы: 30

Бренд: Milwaukee Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды