Lippert SlimRack Скачать руководство пользователя

Страница: 3 / 24

Rev: 01.07.22

Page 3

CCD-0001459

1510000276 / 366703

(Winnebago)

Discontinued -

replaced by 697096 or 700156

and harness 387587

Fig. 3

Product Information

The Lippert SlimRack Slide-Out system is a rack-and-pinion design operated by a 12V DC gear motor. Slide-

out systems are engineered to provide years of trouble-free service. Changes to weight, stroke, weight

distribution, gear rack position, controller, power supply seals, slide toppers, ramps, rollers, etc., all have

an effect on the performance of the system. In order to secure warranty coverage, each new application

or changes to existing applications

MUST

be audited and approved by Lippert Components with a signed

document. Audits can be arranged by contacting Lippert Components.
This manual provides information for slide-out systems that use one of three different controllers: Power Gear

part number 1510000199 / Lippert part number

366697

,700155, 700157 (Fig. 1), Power Gear part number

1510000236 / Lippert part number

366701

697096, 700156 (Fig. 2) or Power Gear part number 1510000276 /

Lippert part number 366703 (Fig. 3). Controller Power Gear part number 1510000199 / Lippert part number

366697

connects to a touchpad. Controller part numbers (Power Gear / LCI) 1510000236 /

366701

and

1510000276 / 366703 connect to a rocker switch.

NOTE:

Previously, some Winnebago models used controller Power Gear part number 1510000276

/ Lippert part number 366703 (Fig. 3) which required a wire harness with an 8-pin connector

for connecting the controller to Motor 2 (Fig. 3A). For all new units, Power Gear part number

1510000276 / Lippert part number 366703 has been replaced by number 697096 or 700156. For

servicing older Winnebago units, controller Power Gear part number 1510000276 / Lippert part

number 366703 has been replaced with controller part number 697096 or 700156 with an added

adapter wire harness 387587 (see section Wiring Diagram for controller 1510000276 / 366703 (WGO

- Discontinued.)

1510000199 / 366697

Fig. 1

1510000236 / 366701

Fig. 2

700155

700156

700157

697096

NOTE:

All the controllers that are being replaced by the new controllers. Refer to New Slim Rack Controller

QR-124 document.

Replacements

Содержание SlimRack

























Результаты поиска

Содержание SlimRack

Отзывы:

Похожие инструкции для SlimRack

Бренды по названию

Популярные бренды

Lippert SlimRack, Руководство пользователя

Результаты поиска

Содержание SlimRack

Отзывы:

Похожие инструкции для SlimRack

Бренды по названию

Популярные бренды