background image

Rev: 10.15.20

Page 8

CCD-0003688

2. 

If the light pod is lit green, and no error codes are detected, place the Sway Command warning sticker 

(Fig. 7A) on the outside of the caravan's A-frame next to the light pod.

What is happening?

Why?

What should be done?

Off

Sway Command is not 

powered and not active.

Sway Command is in low power. Activate tow 

vehicle brake to wake up Sway Command.
Sway Command is not connected to DC 12V 

power supply. Verify wiring.

Green, Red, Repeat

Wake up self-checks 

in progress

After a few seconds, the Sway Command will 

complete self-checks, and set the lights green if 

Sway Command is ready, or a flashing code if an 

issue is found.

Green Solid

Sway Command is 

awake and monitoring 

for sway.

Every five seconds there will be a brief time the 

green LED turns off for a fraction of a second. This 

indicates Sway Command is functional.

Red Blink (1/2 second 

on, 1/2 second off, 

repeats)

Sway Command 

detected sway event 

and is activating brakes.

After sway subsides, light will return to green.

Green, 2 Red

A short to 12 volt 

detected

Verify blue brake wire not shorted to 12 volt.

Green, 3 Red

Not connected to 

caravan brakes.

Verify the blue brake wire is connected to the 

caravan brakes.

Green, 4 Red

A short to ground 

detected.

Verify the blue brake wire is not shorted to ground or 

caravan frame.

Green, 5 Red

Low voltage detected.

Verify tow vehicle and tow battery are at 12 volts.

Red Solid

Sway Command is not 

functional.

Disconnect harness, wait 10 seconds. 

Connect harness.

Red Fast Blink 

(100ms on, 100ms 

off, repeats)

Sway Command is not 

functional.

Disconnect harness. Wait 10 seconds then connect 

harness. If light comes on solid red, unplug Sway 

Command and contact service department.

Fig. 7 

Light Codes and Troubleshooting

In the event a tow vehicle brake controller detects a fault after Sway Command detects a sway event, 

manually activate the tow vehicle brake controller a few times to clear the fault.

A

Содержание Sway Command











Отзывы: