Lippert Components Ground Control 2.0 Скачать руководство пользователя страница 127

Страница: 127 / 166

Rev:11.08.19

Page 127

CCD-0001573-08

Safety

The “WARNING” symbol above is a sign that a service or maintenance procedure has a safety risk

involved and may cause death or serious injury if not performed safely and within the parameters

set forth in this manual.

Always wear eye protection when performing service or maintenance to the vehicle. Other

safety equipment to consider would be hearing protection, gloves and possibly a full face shield,

depending on the nature of the service.

Failure to correctly service the vehicle may result in death, serious injury or property damage.

• Never allow anyone unfamiliar with this product to install, operate or service this product.

• Never lift or level the trailer without a properly installed footpad.

• Never crank the jack or couple the trailer without preventing the trailer from rolling.

• Never exert excessive side forces to the power tongue jack.

• Never allow anyone, including the operator, to put any body parts under the power tongue jack or

the supported load during jack operation.

• Never drop the trailer off the hitch ball.

• Never exceed the load capacity.

• Never use the power tongue jack to lift the trailer for service or tire change.

• Never move the trailer before the power tongue jack is fully retracted.

• Never use the power tongue jack unless the footpad clevis pin and hairpin cotter pin are fully

inserted through both sides of the jack’s inner tube.

Содержание Ground Control 2.0







































































































































































Результаты поиска

Содержание Ground Control 2.0

Отзывы:

Похожие инструкции для Ground Control 2.0

Бренды по названию

Популярные бренды

Lippert Components Ground Control 2.0, Руководство владельца

Результаты поиска

Содержание Ground Control 2.0

Отзывы:

Похожие инструкции для Ground Control 2.0

Бренды по названию

Популярные бренды