background image

 

 

 

Instructions 

Saddle-mount unit GSG-S-VM 

 

   

 

 

11 - 72

 

 010710-03-EN BA GSG-S-VM / 13.07.2020

 

 

 

 

7.  Accident prevention 
 
Failure to comply with the simplest basic rules are causing most ac-
cidents occurring during use, maintenance or transport. 
 
Therefore,  it  is  important  that  all  persons  involved  with  use  of  the 
machine are aware of and comply with the following rules: 
 

 

In order  to  achieve  maximum  performance  from  the 

GSG-S-VM 

it must be in proper working condition. Perform maintenance and 
repair only by trained people. 

 

 

Replacement  parts  must  fulfill  the  minimum  technical  specifica-
tions  required  by  the  manufacturer!  Only  use  of 

LIPCO  original 

replacement parts

 will fulfill these requirements. 

 

 

Before  each  use,  check  the  trailer  hitch  bolts  on  the  three-point 
mount and all studs and nuts! 

 

 

Exercise special Note when using roads or paths, e.g. for turning 
the entire tunnel spray unit. 

 

 

Always shut off the motor and remove the ignition key when per-
forming maintenance or repairs! 

 

 

During  work  and  transport  on  public  road,  do  not  transport  ob-
jects or persons on the machine! 

 

 

Operate  machine  only  with  drive  unit  fully  protected,  i.e.  univer-
sal  joint  shaft  completely  covered  and  additional  protection  on 
tractor  and 

GSG-S-VM.

  Make  sure  that  the  universal  joint  shaft 

connections lock securely into place! 

 

 

The  machine  should  be  on  a  level  surface  or  a  stable  support 
during all work on the machine! 

 

When working on the machine in raised position, always secure 
by mechanical means using suitable supports! 

 
 

Содержание GSG-S-VM









































































Отзывы: