LineEye LE-2500XR Скачать руководство пользователя страница 34

Страница: 34 / 140

-32-

Expansion Interfaces

Expansion boards widen the targets of communications.

Exchange interface board

Remove the standard interface board first, then exchange to

the optional interface board.

〇

SYNC-clock TTL communication

Use OP-SB5GL

〇

In-vehicle communication

CAN/CAN FD/CXPI

Use OP-SB7XC

Firmware for expansion board

Firmware for expansion board is available at LINEEYE web page. Write the firmware into the analyzer using

“le8firm.exe” which is stored in the attached CD. Once writing the firmware into the analyzer, appropriate

firmware will automatically run according to the inserted interface board.

10.5

Firmware Update

For optional firmware “OP-FW10XR”, press [SHIFT]+[0] or [SHIFT]+[3] to exchange the standard firmware and op

tional firmware.

〇

In-vehicle communication

CAN/CAN FD/LIN

Use OP-SB7XL

〇

Current-loop communication

Use OP-SB1C

Send loop

Reception loop

Connect with probe

Содержание LE-2500XR













































































































































Результаты поиска

Содержание LE-2500XR

Отзывы:

Похожие инструкции для LE-2500XR

Бренды по названию

Популярные бренды

LineEye LE-2500XR, Инструкция по эксплуатации

Результаты поиска

Содержание LE-2500XR

Отзывы:

Похожие инструкции для LE-2500XR

Бренды по названию

Популярные бренды