1
FS20Z-1 ISOLATED CONTACT FIXTURE MODULE
Linear’s family of Z-Wave certifi ed wireless lighting controls (switches,
dimmers, outlets and plug-in modules) brings a new level of intelligent
wireless capability to commercial and residential environments.
The Z-Wave wireless protocol is an international wireless standard
for remote home automation, security and other applications.
Embedded in each device, the Z-Wave smart chip enables two-way RF
communication among hundreds of Z-Wave enabled devices, allowing
products and services from multiple manufacturers to work seamlessly.
Linear Z-Wave products are easy to install, and allow dealers to create
an integrated wireless network with nearly limitless expansion and
interoperability with security and health monitoring systems, energy
management, home entertainment, appliances, and more.
DANGER! SHOCK HAZARD.
Read and understand these
instructions before installing. This device is intended for installation in
accordance with the National Electric code and local regulations in the
United States, or the Canadian Electrical Code and local regulations
in Canada. It is recommended that a qualifi ed electrician perform this
installation. For indoor use only. Retain instructions for future use.
INSTALLATION
Wire this module in series with a (maximum) 20 amp load according
to the diagram above. FS20Z-1 are required to be
wired to the same
line (or neutral)
which is also wired to the master unit as well as the
load being controlled, and not wired to any other neutral. If multiple
neutrals are tied together in one box, separate the neutrals to preserve
the integrity of the FS20Z-1 circuit.
Fixture Mounted Confi guration
Push the button on the face to confi gure the module to operate from the
wireless controller. With the Wireless Controller, the FS20Z-1 can be
switched ON and OFF remotely, and can be included in groups of lights
that operate at the same time (a group can also be a single module),
and in scenes that set a lighting mood.
Other Functions
The button on the FS20Z-1 also plays a role as a reset in addition to
including the module in groups and scenes. This is described in more
detail in the Wireless Controller instructions.
Over-current Protection
The FS20Z-1 is protected by an internal fuse. This internal fuse is
factory serviceable only. Check your home circuit breakers before
concluding that the product must be returned to manufacturer for repair
at a nominal charge.
Button (Local Control)
The button on the FS20Z-1 allows the user to:
• Turn the load attached ON or OFF.
• Include or exclude the module in the Z-Wave system:
STEP 1.
Prepare the Controller to include a unit to the network by
adding it to a group (method of adding a node to the network). Refer to
controller instructions.
STEP 2. The FS20Z-1
must be in its permanently installed location.
• To add a node:
Tap the button.
• To remove a node:
Tap the button 3 times, then press and hold (Ex.
tap, tap, tap, hold)
STEP 3.
You should see an indication on your Controller that the
“DEVICE WAS INCLUDED” or “DEVICE WAS EXCLUDED” in the
network. If attached, an FS20Z-1 ver.2 auxiliary switch can also be
used to Include or Exclude the module from the Z-Wave system. When
a controller prompts you to “Send Node ID” or to “Press Button on Unit”,
follow steps 1 through 3 above to satisfy those instructions.
LED Indication
The LED on the FS20Z-1 will turn on when the load attached is ON.
The LED can be user confi gured however to turn ON when the load
attached is OFF, if so desired. The FS20Z-1 will fl icker its LED when it
is transmitting to any of its 4 groups. This can be changed if desired.
Remote Control
The FS20Z-1 will respond to BASIC and BINARY and SCENE
commands that are part of the Z-Wave system. Refer to your
controller’s instructions as to whether your controller can transmit those
commands.
FS20Z-1
Radio Frequency (RF) Controlled, 120 VAC, Scene Capable,
Isolated Contact Fixture Module, Series 300
P1753
3B54M
FS20Z-1
Fixture Module Receiver
Series 300,
Rel. 5.41
S/N
120 Volts A
C, 60 Hz 908.42 MHz
Isolated Output Contact Ratings (UL/CUR)
277V
AC, 5540W (max), 20 Amp
, Resistiv
e 120/240V
AC
1/2 HP Motor
, 120V
AC, 960W Incandescent Load
WARNING:
Do not e
xceed electr
ical ratings
.
FCC ID:
QIE0791-01
Canada IC:
4436A-079101
Linear LLC
, Car
lsbad, CA
BLK: Line
, WHITE:
Neutr
al,
BLUE:
Load, GRN:
Ground
STATUS LED
PUSH BUTTON TO
ADD NODE TO NETWORK
GREEN GROUND
NEUTRAL
WHITE
120 VAC
LINE
BLACK
BLUE
BLUE
FS20Z-1 LOAD MUST SHARE THE SAME PROPRIETARY NEUTRAL
LOAD
20 AMPS
MAXIMUM
24 TO 277V
