FCC & IC Notice
This device complies with Part 15 of the FCC Rules and Industry Canada
license exempt standard(s). Operation is subject to the following two
conditions:
1) This device may not cause harmful interference, and
2) This device must accept any interference received, including
interference received that may cause undesired operation.
Le présent appareil est conforme aux CNR d’Industrie Canada
applicables aux appareils radio exempts de licence. L’exploitation est
autorisée aux deux conditions suivantes:
1) l’appareil ne doit pas produire de brouillage, et
2)
l’utilisateur de l’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d’en
compromettre le fonctionnement.
WARNING:
Changes or modifi cations not expressly approved by the
manufacturer could void the user’s authority to operate the equipment.
IMPORTANT !!!
Linear radio controls provide a reliable communications link and fi ll an
important need in portable wireless signaling. However, there are some
limitations which must be observed.
• For U.S. installations only: The radios are required to comply with
FCC Rules and Regulations as Part 15 devices. As such, they have
limited transmitter power and therefore limited range.
• A receiver cannot respond to more than one transmitted signal at
a time and may be blocked by radio signals that occur on or near
their operating frequencies, regardless of code settings.
• Infrequently used radio links should be tested regularly to protect
against undetected interference or fault.
• A general knowledge of radio and its vagaries should be gained
prior to acting as a wholesale distributor or dealer, and these facts
should be communicated to the ultimate users.
Delta-3 Series
miniTransmitter
Digital Transmitter
Code Setting Instructions
USA & Canada (800) 421-1587 & (800) 392-0123
(760) 438-7000 - Toll Free FAX (800) 468-1340
www.nortekcontrol.com
Copyright © 2019 Nortek Security & Control LLC
106914 E
PRINTER’S INSTRUCTIONS:
INSTR,CODE SET,MINI XMTR - P/N: 106914 E - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 8.500” X 5.500” - TOL/- .125” SCALE: 1-1 - PRINT 2 SIDES
LIMITED WARRANTY
This Nortek Security & Control LLC product is warranted against defects
in material and workmanship for twenty-four (24) months. This warranty
extends only to wholesale customers who buy direct from Nortek or
through Nortek’s normal distribution channels. Nortek Security & Control
LLC does not warrant this product to consumers. Consumers should
inquire from their selling dealer as to the nature of the dealer’s warranty,
if any. There are no obligations or liabilities on the part of Nortek Security
& Control LLC for consequential damages arising out of or in connection
with use or performance of this product or other indirect damages
with respect to loss of property, revenue, or profi t, or cost of removal,
installation, or reinstallation. All implied warranties, including implied
warranties for merchantability and implied warranties for fi tness, are
valid only until the warranty expires. This Nortek Security & Control LLC
Warranty is in lieu of all other warranties express or implied.
All products returned for warranty service require a Return Authorization
Number (RA#). Contact Nortek Security & Control Returns at
1-855-546-3351 for an RA# and other important details.
WARNING:
Changes or modifi cations not expressly approved by the
manufacturer could void the user’s authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the Federal
Communications Commission (FCC) rules. These limits are designed
to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
