■ Start Counting
■ Before Start Counting
[
Setting Date and Time
]
YYYY
MM
DD
hh
mm
●Press Power Key for 1 second to turn up the device.
●Push Count Key with Key pressed.
Now you can start setting date and time.
●Date and Time will be displayed on LCD of the device as shown below
in the manner of "YYYY MM DD hh mm."
●Every time you push each Count Key, each corresponding figure of
year, month, day, hour or minute will be increased.
When you push each Count Key with Key pressed,
each corresponding figure will be decreased.
●Push Key after you input date and time.
Now the setting of date and time is finished, and you can start counting.
●If you proceed with counting, refer to the next section "■Start Counting."
If you want to turn off the device, press Power Key for 3 seconds.
F
F
1
YYYY MM DD hh mm
1
=year
2
=month
3
=day
4
=hour
5
=minute
SUB
DK-5005A Start Guide
*
NOTE
If the power supply is shut off, the built-in clock stops. This requires
resetting of Date & Time
when you use the device next time.
To avoid stopping the clock, please install batteries into the device. As long as the electricity is supplied to the device through AC/DC adapter or USB charging cable,
power is not supplied nor drained from batteries. Therefore, it is recommended that batteries be always installed in the device even if the electricity is supplied to the
device through AC/DC adapter or USB charging cable.
●Press Power Key for 1 second to turn up the device.
●On its LCD, the device displays count values of 5 counters, total count of 5 counters,
and time.
●Every time you push Count Key - , the count value of each counter
increases.
By pushing each Count Key with Key pressed, each count value decreases.
■ Save Record (Count value)
TIME
Count value of each counter
Total count of 5 counters
Time
1
5
TIME
1
2
3
4
5
SUB
The device can save up to 250 "records."
A "record" is timestamped data containing 5 count values and total count value.
1 record = (Individual Count Values) + (Total count of 5 counters) + (Date&Time
)
There are two ways to save a record.
*
NOTE
If you turn off the device without resetting count values to 0 (zero), the last count
values will internally remain.
Next time you turn up the device, you can start counting from the last count values.
but if you want to reset the values to 0 (zero), press Key for 1 second.
#
■ Name of Each Part of DK-5005A
7
1
SUB
DK-5000 Series
F
2
3
4
5
#
POWER
YYYY
MM DD hh mm
TIMEM
SUB
8
1
2
3
4
5
6
9
10
15
14
11
12
13
Clock / Memory No.Display
Count Display
Date/Time Icon
Subtract Icon
Low Battery Icon
Software Link Icon
5.5 mm DC Jack
Power Key
[#] Key
Count Key
Subtract Key
Strap Hole
Function Key
USB 2.0 Port
Total Count Display
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
[
1. Save Record with Resetting Count Values to 0 (zero)
]
●Press Key for 1 second at the count values that you want to save.
●LCD starts to blink, and count value of each counter and total count value will be
saved with timestamp.
●LCD stops blinking when saving the record is completed.
Each count value is reset to 0 (zero).
●Now you can start counting again.
#
TIME
[
2. Save Record without Resetting Count Values to 0 (zero)
]
●Push Count Key with Key pressed at the count values that you
want to save.
●LCD starts to blink, and count value of each counter and total count value will be
saved with timestamp. Each count value will not be reset to 0 (zero).
●LCD stops blinking when saving the record is completed.You can continue counting.
F
5
LINE SEIKI CO., LTD.
