Lincoln ZPU 08 Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 57

Lincoln ZPU 08 Скачать руководство пользователя страница 31

Operating Instructions

Pump ZPU 08 ATEX

810-53711-1

Page 31 / 57

Rev.: 003
31/07/2017

4.12.

Electrical connection

Connection must be done in such way that a permanent, safe electrical connection
can be maintained (use safe protective conductor connection and dedicated cable
ends; avoid protruding wire ends). Make sure that there are no foreign particles,
dirt or humidity in the terminal box. Close the terminal box dust- and watertight.
In addition to the general valid installation prescriptions for electrical systems, the
electrical connection is carried out in accordance with the applicable national ATEX
regulations, for example:



ElexV



DIN EN 60079-14:2014, VDE 0165-1:2014
Electrical systems in explosive areas



DIN EN 60079-17:2014
Electrical equipment for use in areas with combustible dust



DIN VDE 0100

Tolerance voltage

± 5 %

Tolerance frequency ± 2 %
The waveform and mains symmetry must be maintained so that the motor heat-up
remains within the permitted limits.
The distance to any voltage-carrying or conductive parts has to correspond to the
minimum values following DIN EN 60079-7:2007 / VDE 0170-6:2007.

Nominal voltage

Distance to motors

Ex category 2

For motors up to 500 V

5 mm

4.13.

IP Types of protection

gear

Motor

Capacitive sensor

Terminal box

IP 65

IP 55

IP 67

IP 65

«
...
29
30
31
32
33
...
»

Содержание ZPU 08


























































Отзывы:

Нет отзывов