manualshive.com logo in svg

Lincoln POWER MIG 350MP, Руководство оператора

Поделиться
Скачать
Lincoln POWER MIG 350MP Скачать руководство пользователя страница 1

POWER MIG

®

350MP

OPERATOR

ʼ

S

 

MANUAL

IM859

May, 2012

Safety Depends on You

Lincoln arc welding and cutting
equipment is designed and built
with safety in mind. However,
your overall safety can be
increased by proper installation
... and thoughtful operation on
your part. 

DO NOT INSTALL,

OPERATE OR REPAIR THIS
EQUIPMENT WITHOUT READ-
ING THIS MANUAL AND THE
SAFETY PRECAUTIONS CON-
TAINED THROUGHOUT.

And,

most importantly, think before
you act and be careful.

For use with machine Code Numbers: 11147

For use with machine

• Sales and Service through Subsidiaries and Distributors Worldwide •

Cleveland, Ohio 44117-1199  U.S.A.   TEL: 216.481.8100   FAX: 216.486.1751   WEB

 

SITE: www.lincolnelectric.com

• World's Leader in Welding and Cutting Products •

Copyright © Lincoln Global Inc.

This manual covers equipment which is no 
longer in production by The Lincoln Electric Co.  
Specifications and availability of optional 
features may have changed.

Содержание POWER MIG 350MP
















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды