Lincoln Electric SAE-300 HE Скачать руководство пользователя страница 60

Страница: 60 / 84

LINCOLN ELECTRIC

SAE-300® HE Service Manual

CHOKE TEST PROCEDURE

Service and repair should be performed by only Lincoln Electric factory trained personnel. Unauthorized

repairs performed on this equipment may result in danger to the technician or machine operator and will

invalidate your factory warranty. For your safety and to avoid electrical shock, please observe all safety

notes and precautions detailed throughout this manual. If for any reason you do not understand the test

procedures or are unable to perform the test/repairs safely, contact the Lincoln Electric Service Department

for electrical troubleshooting assistance before you proceed. Call 1-888-935-3877.

TEST DESCRIPTION

This test will determine if the Choke is open, shorted (turn to turn) or grounded.

MATERIALS NEEDED

Volt/Ohmmeter

Wiring Diagram

TEST PROCEDURE

Turn off the engine on the SAE-300 HE machine.

Open the side covers and secure them with the hooks provided.

Locate the choke assembly (attached to the rear of the front panel) and perform the following tests.

See Wiring Diagram.

Open:

No weld output. Using a volt/ohmmeter, test the resistance from the top choke terminal to

the negative output terminal. See Wiring Diagram. Typical resistance is less than one ohm.

Turn To Turn Short:

Reduced inductance, arc instability, excessive heating of the choke. Check for

any physical signs of arcing within the choke assembly. See Wiring Diagram.

Choke Coil Grounded:

Reduced inductance, alternate weld current path. Electrically isolate the

choke coil by disconnecting the leads from the top and bottom choke terminals. Using a

volt/ohmmeter, check the resistance from choke coil to chassis ground. Resistance should be at

least 500,000 ohms. See Wiring Diagram.

If any of the tests fail, the choke may be faulty.

If faulty, perform the

Choke Removal And Replacement Procedure

Connect any previously disconnected leads and close the side covers. See Wiring Diagram.

Содержание SAE-300 HE




















































































Результаты поиска

Содержание SAE-300 HE

Отзывы:

Lincoln Electric SAE-300 HE, Руководство по обслуживанию, Страница: 60 / 84

Результаты поиска

Содержание SAE-300 HE

Отзывы: