Lincoln Electric SAE-300 HE Скачать руководство пользователя страница 59

Страница: 59 / 84

LINCOLN ELECTRIC

SAE-300® HE Service Manual

ENGINE ALTERNATOR TEST PROCEDURE

Service and repair should be performed by only Lincoln Electric factory trained personnel. Unauthorized

repairs performed on this equipment may result in danger to the technician or machine operator and will

invalidate your factory warranty. For your safety and to avoid electrical shock, please observe all safety

notes and precautions detailed throughout this manual. If for any reason you do not understand the test

procedures or are unable to perform the test/repairs safely, contact the Lincoln Electric Service Department

for electrical troubleshooting assistance before you proceed. Call 1-888-935-3877.

TEST DESCRIPTION

This test will determine if the Engine Alternator is functioning normally.

MATERIALS NEEDED

Volt/Ohmmeter

Wiring Diagram

TEST PROCEDURE

Turn off the engine on the SAE-300 HE machine.

Open the side covers and secure them with the hooks provided.

Locate the engine alternator on the back left side of the engine. See Wiring Diagram.

Using a volt/ohmmeter, perform the tests outlined below. See Wiring Diagram.

Place the ‘Run/Stop’ switch into the ‘Stop’ position and test the following points:

• Chassis ground to the B+ terminal of the alternator (Lead #51), the meter should read battery

voltage.

• Chassis ground to the alternator flash/sense lead (Lead #59). The meter should read 0 volts.

Place the ‘Run/Stop’ switch into the ‘Run’ position and test the following points:

• Chassis ground to the flash/sense lead (Lead #59), the meter should read 11.5 to 12.9 VDC during

first 30 seconds of operation (This time may be 60 seconds on some models).

Start the engine and test the following points:

• Chassis ground to the B+ terminal of the alternator (Lead #51). The meter should read about 13.5

to 14.2 VDC.

• Chassis ground to the alternator flash/sense lead (Lead #59). The meter should read about 10

VDC.

If the voltages are significantly different from those shown above, check the wiring connected to the

alternator for faulty connections or bad insulation. If the wiring is good, the alternator is probably

faulty and should be serviced or replaced be replaced.

When testing is complete, close the side covers.

Содержание SAE-300 HE




















































































Результаты поиска

Содержание SAE-300 HE

Отзывы:

Lincoln Electric SAE-300 HE, Руководство по обслуживанию, Страница: 59 / 84

Результаты поиска

Содержание SAE-300 HE

Отзывы: