Lincoln Electric SA-400I Скачать руководство пользователя страница 14

Страница: 14 / 68

A-6

INSTALLATION

SA-400I

BATTERY CHARGING

The SA-400I

is equipped with a wet charged battery. The

charging current is automatically regulated when the battery is
low (after starting the engine) to a trickle current when the bat-
tery is fully charged.

When replacing, jumping or otherwise connecting the battery to
the battery cables, the proper polarity must be observed. This

system is

NEGATIVE GROUND

GASES FROM BATTERY can explode.
• Keep sparks, flame and cigarettes away.

BATTERY ACID can burn eyes and skin.

• Wear gloves and eye protection and be

careful when boosting, charging or work-

ing near battery.

To prevent EXPLOSION when:

a) Installing a new battery - disconnect thenegative cable

from the old battery first and connect the negative cable

to the new battery last.

b) Connecting a battery charger - remove the battery from

the welder by disconnecting the negative cable first, then

the positive cable and battery clamp. When reinstalling,

connect the negative cable last.

c) Using a booster - connect the positive lead to the battery

first, then connect the negative lead to the ground lead on

the base.

To prevent ELECTRICAL DAMAGE when:

a) Installing a new battery.

b) Using a booster.

Use correct polarity - Negative Ground.

To prevent BATTERY DISCHARGE, if you have an ignition

switch, turn it off when engine is not running.

• To prevent BATTERY BUCKLING, tighten nuts on battery

clamp until snug.

WARNING

Содержание SA-400I





































































Результаты поиска

Содержание SA-400I

Отзывы:

Бренды по названию

Популярные бренды

Lincoln Electric SA-400I, Руководство оператора

Результаты поиска

Содержание SA-400I

Отзывы:

Бренды по названию

Популярные бренды