Lincoln Electric MAGNUM &MAGNUM PROCURVE 200 K2950 Скачать руководство пользователя страница 1

Страница: 1 / 21

MAGNUM & MAGNUM PRO CURVE 200

GMA GUN and CABLE ASSEMBLY

OPERATOR’S MANUAL

IM434-C

November, 2010

Safety Depends on You

Lincoln  arc  welding  and  cutting
equipment  is  designed  and  built
with  safety  in  mind.  However,
your  overall  safety  can  be
increased  by  proper  installation
...  and  thoughtful  operation  on
your  part.

DO NOT INSTALL,

OPERATE  OR  REPAIR  THIS
EQUIPMENT  WITHOUT  READ-
ING  THIS  MANUAL  AND  THE
SAFETY  PRECAUTIONS  CON-
TAINED  THROUGHOUT.

And,

most importantly, think before
you act and be careful.

Models

K497
K2950

• Sales and Service through Subsidiaries and Distributors Worldwide •

Cleveland, Ohio 44117-1199 U.S.A. TEL: 216.481.8100 FAX: 216.486.1751 WEB SITE: www.lincolnelectric.com

• World's Leader in Welding and Cutting Products •

MAGNUM

MAGNUM PRO CURVE

Содержание MAGNUM &MAGNUM PROCURVE 200 K2950






















Результаты поиска

Содержание MAGNUM &MAGNUM PROCURVE 200 K2950

Отзывы:

Похожие инструкции для MAGNUM &MAGNUM PROCURVE 200 K2950

Бренды по названию

Популярные бренды

Lincoln Electric MAGNUM &MAGNUM PROCURVE 200 K2950, Руководство оператора

Результаты поиска

Содержание MAGNUM &MAGNUM PROCURVE 200 K2950

Отзывы:

Похожие инструкции для MAGNUM &MAGNUM PROCURVE 200 K2950

Бренды по названию

Популярные бренды