background image

Page 27

Pumping Methods and Patterns

Pumping Methods and Patterns

Follow one of these pumping methods and follow the pattern unless 
otherwise prescribed by your physician or health care professional.

Double pumping

Pumping both breasts at the same time is recommended as it yields 
higher milk volume. This method takes approximately 15-20 minutes. 

See “Double Pumping Setup” on page 22

.

Single pumping

For single pumping, 

see “Single Pumping Setup” on page 23

.

1.  If the infant has suckled on one breast, or one breast does not 

need pumping for some other reason, milk may be expressed 
from the second breast continuously, which takes approximately 
15-20 minutes.

2.  If both breasts are to be pumped, express milk from one breast 

at a time, switching sides as indicated below. This method takes 
approximately 30 minutes.

•  

Pump first breast for 7 minutes.

•  

Pump second breast for 7 minutes.

•  

Go back to the first breast for 5 minutes.

•  

Then go to second breast for 5 minutes.

•  

Go back to first breast for 3 minutes.

•  

Then pump second breast for 3 minutes.

Содержание PJ's Comfort














































Отзывы: