Lika MTA1 Скачать руководство пользователя | Manualshive

Страница: 43 / 48

background image

SMA1

9 - Error and fault diagnostics

In case of wrong alignment between the sensor and the magnetic scale, at
power on or during operation the following errors may occur:



the LED lights up when switching on the system: there is a wrong
alignment; it may cause invalid data to be transmitted; please install the
sensor properly; as soon as the sensor is aligned correctly the LED switches
off;



the LED lights up during operation: the last valid position is “frozen” (kept in
memory) until the next valid position is detected on the scale.

9.1 Diagnostic LED

When the LED lights up, it indicates that an error is active, such as for instance
an incorrect alignment between the sensor and the scale:



the gap between the sensor and the scale is out of tolerance (see Figure 2)



the sensor is not installed properly



the sensor or the scale are installed upside down



the sensor is installed in the opposite direction to the one shown in the
Figure 1



the sensor is travelling too fast



the power supply is not as required

With BiSS interface, the device status is transmitted via the

nE

bit (see the

Error

bit on pages 22 and 32).

NOTE

When the LED is off, this means that the sensor is working properly and the
absolute position is output correctly. Please note that the sine-cosine signals
does not affect the LED operation.

For further information refer also to the “11 - Troubleshooting” section on page
45.

MAN SMA1 E 2.9.odt

9 - Error and fault diagnostics

43 of 48

«
...
41
42
43
44
45
...
»

Содержание MTA1

















































Отзывы:

Нет отзывов

Похожие инструкции для MTA1

Бренд: Patton electronics Страницы: 12

Бренд: Data Translation Страницы: 62

Бренд: Xantrex Страницы: 78

Бренд: Xanter Страницы: 54

Бренд: K&S BASIC Страницы: 17

Бренд: Danfoss Страницы: 292

Music Maker 2396

Бренд: Califone Страницы: 1

Бренд: All-Power Страницы: 35

Бренд: Planet Страницы: 32

Бренд: NAIM Страницы: 22

DASNET-SPLITTER

Бренд: D.A.S. Страницы: 12

Бренд: Digitus Страницы: 6

Бренд: SIIG Страницы: 12

Бренд: Majella Страницы: 6

Q.VOLT-G2 HYB-4.6kW.1.1

Бренд: Q CELLS Страницы: 118

ECO Inverter+ 7

Бренд: Oilon Страницы: 58

SINEMASTER IG4300

Бренд: Kipor Страницы: 50

Бренд: Xantrex Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды