Quick Start Guide
WP-HDMI-TPS-TX97-EU, -EUROMOD, -UK, -US
FP-HDMI-TPS-TX97-GB3, -LEGRAND, -CRFB
Further Information
The product brief and further information of this appliance is available at
www.lightware.com
.
See the
Downloads
section on the website of the product.
Contact us
+36 1 255 3800
+36 1 255 3810
Lightware Visual Engineering LLC.
Peterdy 15, Budapest H-1071, Hungary
Doc. ver.: v1.1
19200089
Important Safety Instructions
Please read and keep the information in the attached safety instructions supplied with the
product before you start using the device.
Introduction
WP/FP-HDMI-TPS-TX97 series twisted pair HDBaseT
TM
extenders provide
extension of uncompressed 4K/UHD video with embedded audio (up to eight
channel PCM or HBR audio) for long distances over a single CATx cable.
The thoroughly redesigned form factor of the wall and floor panels allows for easier
connecting and removing cables in narrow spaces (behind TV sets, under floor panel lids)
and reduces cable bending and breaking. The built-in cable tie-down points further ensure
stable connection and reduce cable stress.
Box Contents
Transmitter unit
Safety and Warranty info,
Quick Start Guide
Phoenix combicon
3-pole connector
1
Status LEDs
The LEDs give feedback about the state of the unit and the
video signals. See Status LEDs for details.
2
IR input/output
2 TRS (3.5mm jack) connectors for Infrared units (IR IN for the
detector, IR OUT for the emitter).
3
RS-232 connector
3-pole Phoenix connector for RS-232 serial port. Firmware
upgrade can also be performed over this interface.
4
Ethernet
Locking RJ45 connector for Ethernet communication.
5
HDMI input
Input for a digital video source. Applied cable shall not be
more, than 20 m (at 1080p) and 5 m (at 4K).
6
TPS output port
Locking RJ45 connector for HDBaseT
TM
signal transmission.
Connect a twisted pair cable between the transmitter and the
receiver.
7
Tie-down point
The built-in tie-down points are designed to clamp the
HDMI and the CATx cable and ensure stable connection.
Please see the enlarged picture below.
Front and Rear View (WP-HDMI-TPS-TX97-US)
Bottom View (WP-HDMI-TPS-TX97-US)
RS-232 Switch Modes
Please note that the 48V power adaptor is an optional accessory which can be purchased
separately.
1
RS-232 switch
Normal:
serial data is passed through the device.
Prog:
RS-232 pass-through function is disabled, the device
is ready for the firmware upgrade (see RS-232 switch
modes section for details).
2
TPS mode switch
LR:
Longreach TPS mode; lower resolution (max 1080p),
longer distances.
Auto:
TPS mode is determined automatically.
3
DC Input
Connect the output to the 3-pole Phoenix connector on the
bottom of the wall plate.
WP-HDMI-TPS-TX97 series have the same connectors but the dimensions are different.
Connecting Steps
CATx
DVI
Connect the TPS output port of the transmitter to the
TPS+PoE
port of the
TPS-PI-1P1 by a CATx cable.
Connect the receiver (or the Matrix input board) to the power injector by a
CATx cable via the TPS port.
HDMI
Connect the source (e.g. Blu-ray player) to the HDMI input port by HDMI cable.
RS-232
Optionally for RS-232 extension: connect a controller/controlled device
(e.g. Touch panel) to the RS-232 port.
IR
Optionally for Infrared extension:
Connect the IR emitter to the IR OUT port of the transmitter, and/or
Connect the IR detector to the IR IN port of the transmitter.
LAN
Optionally connect the transmitter to a LAN.
Power
Powering on the devices is recommended to do as the final step during
the installation. Please check the Power Supply Options section for the
details.
Power Supply Options
TPS-97 extenders are compatible with IEEE 802.3af standard - Power over Ethernet (PoE) -
and can receive power over the TPS line.
The extender can be powered by any of the following ways:
1. Local adaptor
2. Remote power injector
3. Matrix board
TPS-TX/RX90 and TPS-TX/RX95 are not PoE-compatible, thus not able to remote power
the WP-HDMI-TPS-TX/97 series and vica versa. WP-UMX-TPS-TX97 series contains PoE-
compatible remote power function (PD, Powered Device), RX95 and TX95 extenders can be
remote powered only by each other.
Warranty void if damage occurs due to the usage of a different power source.
The product is compatible with any HDBaseT
TM
third party devices.
HDBaseT
TM
and the HDBaseT Alliance logo are trademarks of the HDBaseT Alliance.
Compatible Devices
TPS-97 extenders are compatible with all Lightware devices with TPS port except the TPS-90
series.
Status LEDs
SIGNAL
OFF: no video signal transmission is present.
ON: video signal transmission is present.
LINK
OFF: TPS connection failed between the devices.
BLINKING: TPS connection is detected and Low
Power Partial Functionality (LPPF) link mode is
active.
ON: TPS connection is detected and HDBaseT
TM
(HDBT) or Long reach (LR) link mode is active.
LIVE
OFF: no power supply or out of order.
BLINKING: device is powered and ready to use.
Typical Application
Integrated system diagram
12
3
IR OUT
IR IN
LINK
TX RX
LIVE
SIGNAL
2 3
1
1
5
4
6
LINK
LIVE
SIGNAL
LINK
LIVE
SIGNAL
LINK
LIVE
SIGNAL
switch
Programming
TPS port
RS-232
normal
prog
48V DC
Power
adaptor
TPS-PI-1P1
CATx
(TPS)
Power
send
48V DC
Power
adaptor
MX-
TPS2-
IB-P
DC IN
8 CH
TPS
INPUT
BOARD
WITH
POE
48V
5A
-
+
Ethernet
TPS IN
1 TPS IN
2 TPS IN 3
TPS IN 4
8CH I
NPUT
BO
ARD F
OR HDMI
WIT
H 3D
AND
ANALO
G AUDI
O
MX-HDMI-3D-IB-A
IN 1
IN 2
IN 3
IN 4
MX-
TPS2-
OB-
S
48V
5A
DC
IN
8 CH
TPS
OUTPUT
BOARD
WITH
DIGI
TAL
AUDI
O
12V
power
on TPS
connect
or. Onl
y use
with
compat
ible
devi
ces!
12V
power
on TPS
connect
or. Onl
y use
with
compat
ible
devi
ces!
TPS O
UT 1
TPS OUT 2
TPS O
UT 3
TPS O
UT 4
8CH O
UTPUT
BOARD F
OR HDMI W
ITH
3D AND
ANAL
OG
AUDIO
MX-HDMI-3D-O
B-A OUT
1
OUT
2
OUT
3
CATx
(TPS)
External
power supply
Power send
Typi
cal:
0.5A
Max:
1.25A
- +
Max:2.5A
m
m2 :
NI
P
IR OUT
IR IN
LINK
TX
RX
LIVE
SIGNAL
WP-HDMI-T
PS-T
X97-US
HDMI
IN
E
thernet
LINK
TX
RX
LIVE
SIGNAL
WP-HDMI-T
PS-T
X97-US
HDMI
IN
E
thernet
LINK
TX
RX
LIVE
SIGNAL
WP-HDMI-T
PS-T
X97-US
HDMI
IN
E
thernet
IR OUT
IR IN
IR OUT
IR IN
WP-HDMI-TPS-TX97
Power adaptor
Ethernet
IR emitter
Touch panel
IR
RS-232
LAN
Power
Blu-ray player
HDMI
Compatible
Receiver or
Output Board
TPS-PI-1P1
Power injector
WP-HDMI-TPS-TX97-US
HDMI IN
Ethernet
CATx
CATx
HDMI
HDMI
HDMI
Audio
Audio
MX-
TPS2-
IB-P
DC IN
8 CH
TPS
INPUT
BOARD
WITH
POE
12V
power
on TPS
connect
or. Onl
y use
with
compat
ible
devi
ces!
48V
5
A
- +
Ethernet
TPS IN
1 TPS IN 2
TPS IN
3 TPS IN 4
TPS IN 5
TPS IN
6 TPS IN 7
TPS IN
8
AV Receiver
HDMI-TPS-RX97
Local monitor
Projector
Ethernet
switch
MX-FR17
8CH INPUT
BOARD F
OR HDMI W
ITH 3D
AND
ANAL
OG
AUDI
O
MX-HDMI-3D-IB-A
IN 1
IN 2
IN 3
IN 4
IN 5
IN 6
IN 7
IN 8
MX-
TPS2-
OB-
S
48V
5A
DC IN
8 C
H TPS
OUTPUT
BOA
RD
WITH
DIGI
TAL
AUDI
O
12V
power
on TPS
connect
or. Onl
y use
with
compat
ible
devi
ces!
TPS O
UT 1
TPS O
UT 2
TPS OU
T 3 TPS O
UT 4
TPS OU
T 5 TPS OUT 6
TPS O
UT 7
TPS OU
T 8
S/PDIF I/O
1 S/PD
IF I/O 2
S/PDIF I/O 3
S/PDIF I/O 4
S/PDIF I/O 5
S/PDIF I/O 6
S/PDIF I/O 7
S/PDIF I/O
8
8CH OUT
PUT
BOARD F
OR HDMI
WIT
H 3D
AND
ANAL
OG
AUD
IO
MX-HDMI-3D-O
B-A OUT
1
OUT
2
OUT
3
OUT
4
OUT
5
OUT
6
OUT
7
OUT
8
FP-HDMI-TPS-TX97-GB3
TPS connection
CATx up to 170m
TPS connection
CATx up to 170m
LAN
LAN
LAN
PC
External power
supply
Laptop
Power send
Power send
5.1 speakers
Sn:
Made in EU, Hungary
RoHS
Ethernet 10/100
Bidirectional IR
Bidirectional RS-232
HDMI,
3D, 4K supported
H HDDMM
I I--TTPP
S S--RRXX
9 977
Sn:
T TPPSS
LLoo
n ngg DD
i issttaa
n nccee RR
e ecceeiivv
e err
PIN: 2mm
12V 1A
DC
For best performance use
AWG23
CAT6 or CA
T7 SFTP
cable
Device can be remote powered over TPS link with PoE
(IEEE 802.3af)
TP
S IN
PoE
( )
ETH
ERN
ET
HDMI
FP-HDMI-TPS-TX97-GB3
Ethernet
HDMI In
Serial
cable
HDMI
IR cable
IR emitter
IR OUT
IR IN
LINK
TX
RX
LIVE
SIGNAL
WP-
HDMI-
TPS-T
X97-U
S
HDMI
IN
Ethernet
Power send
TPS connection
CATx up to 170m
Touch panel
IR cable
Serial cable
IR detector
Blu-Ray or
DVD Player
WP- HDMI-TPS
-TX97-US
7
WP-HDMI-TPS-TX97-US
HDMI IN
Ethernet
Safety and
Warranty
Info
Quick
Start
Guide
IR IN
SIGNA
L
HDMI OUT
