Lightware UBEX Series, Руководство пользователя

Страница: 64 / 201

6. Front Panel LCD Menu Operation - Endpoints UBEX series – Matrix Application Mode – User's Manual 64 6. Front Panel LCD Menu Operation - Endpoints UBEX series – Matrix Application Mode – User's Manual 64
MA
TRIX APPLIC
A
TION MODE
Applied F-series endpoint firmware package: v1.4.1 | Applied R-series endpoint firmware package: v1.4.1 | Applied MMU firmware package: v1.2.1 | LDC software: v1.34.0b2
6.5.3. TRX HDMI Output 2 Port
The following information is displayed for the local output port:
▪ Hotplug detect
▪ Signal present
▪ Active resolution
▪ Total resolution
▪ Color space
6.5.4. Overview
The current status of the local (L) and remote
(R) input/output ports is summarized in
the Overview menu. The icons display
information about the port and the
transmitted signals.
TIPS AND TRICKS: Press enter on the
selected port for the settings and detailed
status information.
Icon Icon is blue (inactive) Icon is white (active)
 Sink is not connected Sink is connected
 Signal is not present Signal is present

Signal is not encrypted with
HDCP
Signal is encrypted with
HDCP

No audio signal in the video
stream
Audio is embedded in the
video stream
6.6. EDID Menu
Reduced Advanced EDID Management is
available in the front panel LCD menu which
allows to view an EDID. See more information
about EDID technology in EDID Management
section. The EDID memory structure of
the device can be found in Advanced EDID
Management section.
6.6.1. View
Select the desired EDID memory block:
Factory EDIDs
,
Last Attached EDIDs
,
User
EDIDs
, or
Emulated EDIDs
(only in case of the
transmitter). Select the Name item and press
the knob. Use the jog dial to step between
the EDIDs. The following information can be
checked:
▪ Preferred Resolution
▪ Monitor Name
▪ Audio Info
6.7. System Status Menu
The most important status information is
displayed about the endpoint in the menu.
Device Info
Hardware- and software-related information are listed in the submenu,
e.g.
device label
- this is a user defined unique name which can be set
in the LDC software (see the details in the Status Tab section) or with
LW3 protocol command (see the details in the Set the Device Label
section), and
serial number
,
firmware version
, etc.
Link Status
The current status of the optical or DAC connection, advanced
information about the installed SFP+ modules, and the bonding state
are available under the menu.
Operation
The uptime and the operation time can be read out from the menu.
Temperatures
The recent temperature of the CPU, the system, and the FPGA are
displayed in the menu.
ATTENTION! If the front panel Status LED blinks, check the
temperatures under this menu and ensure the correct air flow for
the device.
Voltages
The recent voltages of the device are displayed in the menu.
WARNING! If the front panel Status LED blinks, power off the
device immediately.
6.8. System Settings Menu
System related settings are available in the menu, e.g. application
mode changing (from matrix mode to extender mode), front panel
settings, reset the device, etc.
6.8.1. Network
The MAC address of the device can be read
out in the menu.
6.8.2. Application Mode
The current application mode (Extender or
Matrix) is displayed in this submenu. For
more details about the two modes see the
Application Modes section.
Follow the steps to change the application
mode to Extender mode:
Step 1.
Navigate to the
System Settings /
Application Mode
submenu.
Step 2.
Select the
Switch Mode...
option.
Step 3.
Confirm the selection, press the
Yes
.
Step 4.
The endpoint changes the application
mode to Extender immediately.
#applicationmode #extendermode
#matrixmode

  

  