Lightware RAP-B511-EU-K Скачать руководство пользователя страница 34

Страница: 34 / 73

5. Software Control - Lightware Device Controller

RAP-B511 series

– User's Manual

5.6.

Event Manager

The feature means that the device can sense changes on its ports and able to react

according to the pre-defined settings. The development idea of the Event manager is

based on users’ feedbacks. In many cases internal events are necessary to display

but it is not easy when the device is hard to access (e.g. built under the desk).

The Event manager can be configured to perform an action if a condition has been detected. E.g. the desired

setup is that after a certain type of IR signal has been detected on S1 port, the device send an RS-232

message. The settings can be done via the LDC in the Control/Events tab, or by LW3 protocol commands.

Configurable events number depends on the device what you are using actually.

Numerous new ideas and requests have been received in connection with the features and settings of the

Event manager since the first release. Therefore, the user interface has been re-designed and many new

functions implemented. The Event editor can be opened by pressing the

Edit

button at each Event.

There is a

grey bar

on the left of the Event panel in each line. If a condition and an action are set and the Event

is enabled, the bar is displayed

in green

Control menu, Event Manager tab

5.6.1.

Event Manager in the RAP-B511

The functionality of the Room Automation Panel based on the Event Manager. UI config page provides an

interface where the events can be set easily and they are saved in the Event Manager. Events from the UI

config page listed backwards (e.g. first event is saved to the E300 slot).
These events are identified by the event name property, which refers to the button (e.g. UIConfig_B11_1) or

the rotary position (e.g. UIConfig_ROT_13).

ATTENTION!

Rename the Events from the UI Config page is highly not recommended!

When one of these events is opened to Edit in the Event Manager, the warning message appears:

The tables below summarize the availablility of the conditions and actions of the RAP-B511.

Conditions

Launch configuration from...

...UI config menu

...Event Manager

Button press /button release





Rotary turn / rotary press





Real-time clock





Infra detector





RS-232 recognizer





GPIO input level change





Actions

Launch configuration from...

...UI config menu

...Event Manager

Button LEDs





Button Interaction State





Ethernet



RS-232



GPIO



The setting is available and recommended to do the configuration from this menu.



The setting is not available in that menu.



Only for advanced users! The setting is available in the Event Manager, but doing the configuration is

highly recommended from the UI config menu.









Содержание RAP-B511-EU-K










































































Результаты поиска

Содержание RAP-B511-EU-K

Отзывы:

Похожие инструкции для RAP-B511-EU-K

Бренды по названию

Популярные бренды

Lightware RAP-B511-EU-K, Руководство пользователя

Результаты поиска

Содержание RAP-B511-EU-K

Отзывы:

Похожие инструкции для RAP-B511-EU-K

Бренды по названию

Популярные бренды