4. Operation of MMX6x2-HT Family
MMX6x2-HT series – User's Manual
27
4.4.3.
Health Status
INFO: The following values are stored in a non-volatile memory and
will not be erased during firmware upgrade.
Voltages
The voltage values are listed measured
internally in the matrix.
Temperatures
The temperature values are listed measured internally in the matrix.
Operational time
The following time values are measured during operation:
▪
Up Time
: The time elapsed from the last boot.
▪
Total Up Time:
The total operational time (updated in every 5
minutes).
▪
Total high temperature Up Time:
The total operational time when
the measured internal temperature was above 70°C (the first 60
seconds is ignored).
ATTENTION!
If the measured internal temperature is above 80°C
(defined as Very High Temperature) for more than 60 seconds, the
matrix is shut down automatically to avoid any damage.
4.4.4.
Inputs Menu
TPS inputs (TPSIN1 and TPSIN2)
▪
HDCP Enable:
Enabled / Disabled
▪
Audio Mode:
Embedded / Aux1 / Aux2 / Aux3 / Aux4. The setting
allows to pre-select the desired audio to the video on the given
TPS input. The setting will be valid on all TPS/HDMI outputs,
where the audio mode is set to Pass-through.
▪
PoE Enable:
Enabled / Disabled
▪
PoE Status:
ON / OFF
▪
TPS Mode:
Auto / HDBaseT / Long
reach / LPPF1 / LPPF2
▪
TPS Status:
Connected
/
Disconnected
¹1V TpsIn1: »
1.03V
½
¹PoE Enable:
Disabled »
¹TPS mode:
HDBaseT
½
TPS outputs (TPSOUT3 and TPSOUT4)
▪
HDMI Mode:
Auto / DVI / HDMI. The
setting determines the output
signal type.
▪
HDCP Mode:
Auto / Always
▪
Pwr5V Mode:
Auto / Always on / Always off. The setting lets the
source and the sink devices be connected – independently
from the transmitted signal.
▪
TPG Mode:
Disabled / Enabled. The test pattern generator can be
switched on/off.
▪
PoE Enable:
Enabled / Disabled
▪
PoE Status:
ON / OFF. If power is sent via the current TPS output,
the status is ON.
▪
TPS Mode:
Auto / HDBaseT / Long reach / LPPF1 / LPPF2
▪
TPS Status:
Disconnected / Connected (Read-only parameter)
Analog audio outputs (AUXOUT1 and AUXOUT2)
▪
Volume:
from -57 to 0 dB, step =
1 dB
▪
Balance
: from 0 to 100, step = 1
(50 = center)
▪
Gain:
from 0 to 3 dB, step = 1 dB
4.4.6.
Signal Info Menu
Basic information is displayed about
the transmitted audio and video in the
submenus: image resolution, refresh
rate, color depth and audio type.
¹HDMI mode:
DVI
½
¹Volume:
-1dB
½
¹Out1 video In...»
Signal Present
HDMI inputs (HDMIIN3 – HDMIIN6)
▪
HDCP Enable:
Enabled / Disabled
▪
Audio Mode:
Embedded / Aux1 /
Aux2 / Aux3 / Aux4. The setting
allows to pre-select the desired
audio to the video on the given
HDMI input. The setting will be valid on all TPS/HDMI outputs,
where the audio mode is set to Pass-through.
Analog audio inputs (AUXIN1 – AUXIN4)
▪
Volume:
from -95 to 0 dB, step = 0.375 dB
▪
Balance:
from 0 to 100, step = 1 (50 = center)
▪
Gain:
from 0 to 21 dB, step = 0.75 dB
4.4.5.
Outputs Menu
HDMI outputs (HDMIOUT1 and HDMIOUT2)
▪
HDMI Mode:
Auto / DVI / HDMI.
The setting determines the output
signal type.
▪
HDCP Mode:
Auto / Always
▪
Audio Mode:
Pass-through / AUX1 / AUX2 / AUX3 / AUX4. The
desired audio can be selected to the video on the given HDMI
output, thus, the setting will override the input setting. In Pass-
through mode, the setting on the input port will be valid.
▪
Pwr5V Mode:
Auto / Always on / Always off. The setting lets the
source and the sink devices be connected – independently
from the transmitted signal.
▪
TPG Mode:
Disabled / Enabled. The test pattern generator can be
switched on/off.
¹HDCP Enable:
Enabled
¼
¹Audio Mode:
Embedded »
¹HDMI mode:
DVI
½
