Lightware HDMI-TP-RX200R Скачать руководство пользователя страница 1

 

www.lightware.eu 

Firmware version: 1.1.8 

For technical support contact [email protected] 

Document revision: 1.0 

HDMI-TP-RX200R 

Quick Start Guide 

Introduction 

The HDMI-TP-RX200R is a HDMI 1.3a compatible Twisted Pair receiver. It includes precise 

manual, or automatic cable equalizing, which is configurable on the front panel. 

Typical application 

 

HDMI-TP-TX and RX200R extender pair 

Installation 

1.

 

Connect the first display (e.g. monitor) to the HDMI OUT 1 connector, 

2.

 

Connect the second display (e.g. projector) to the HDMI OUT 2 connector, 

3.

 

Connect the transmitter or a compatible Lightware device

1

 to the 

a.

 

VIDEO IN with a Twisted Pair cable 

b.

 

DDC IN with another Twisted Pair cable 

4.

 

Supply the unit with +12V 1A DC. The available power supply settings: 

RX jumper configuration 

TX jumper or Matrix Output Board configuration 

 

only local adaptor 

 

only local adaptor 

 

local a remote send to TX 

 

only remote receive from RX 

 

only remote receive from TX 

 

local a remote send to RX 

 

only local adaptor 

 

12V DC IN not connected to Output Board 

 

only remote receive from Output Board   

12V DC IN connected to Output Board 

Change status LEDs’ function 

Press the LEARN button to switch between PRIMARY (SOLID) and SECONDARY (BLINKING) 

mode. 

                                                           

1

 Please check the TP Extension System Cross Compatibility Table in the 

www.lightware.eu

 website 

Status LEDs in PRIMARY (SOLID) mode 

Color 

Function: 

Red 

HDCP ENCRYPTED CONTENT 

Green 

HDMI SIGNAL 

Green 

VIDEO CLOCK PRESENT 

Green 

AUTO CABLE EQUALIZATION ACTIVE 

Status LEDs in SECONDARY (BLINKING) mode 

Color 

Function: 

Red blinking 

EMULATED EDID INVALID 

Green blinking  EMULATED EDID VALID 
Green blinking  OUT1 MONITOR HOTPLUG SENSE 
Green blinking  OUT2 MONITOR HOTPLUG SENSE 

Selecting an EDID 

1.

 

Turn the EDID address rotary switch to the desired memory. 

2.

 

The available EDIDs are listed on the top of the device. 

3.

 

The EDID Status LEDs provide feedback in SECONDARY (BLINKING) mode: 

Red blinking: 

an empty memory or invalid EDID was selected. 

Green blinking:  valid EDID is present at input. 

4.

 

Now the selected EDID is reported on the DDC INPUT. 

EDID Memory 

The available EDIDs are listed on the top of the device (#0..#9). 

 

Address #0 contains a copy of the last recognized monitor’s EDID from HDMI OUT 1. 

 

On  the  address  #1  there  is  an  UNIVERSAL  EDID  to  support  various  resolutions  and 

embedded HDMI audio. 

 

Memory range #2..#8 is user programmable. 

 

Address #9 contains a copy of the last recognized monitor’s EDID from HDMI OUT 2. 

Learning EDID 

1.

 

Turn the Rotary switch to the desired memory address where you want to store the attached 

display's EDID (between user addresses #2..#8), 

2.

 

Connect the desired display device to the HDMI OUT 1. 

3.

 

Press and hold the LEARN button for approximately 2 seconds, 

4.

 

The EDID Status LEDs provide feedback in SECONDARY (BLINKING) mode: 

Red blinking:  

the learn process failed from HDMI OUT 1. 

Green blinking:   the learn process was successful from HDMI OUT 1. 

Info:  Without the Lightware Matrix Controller SW the TX200R can learn only from HDMI OUT 1. 

 

Отзывы: