Instruction Sheet Number
IS:48021
Page
For Assembly and Installation of Soli ADA Series Wall/Ceiling Mounted T-5 Fluorescent
Lightolier
a Genlyte Thomas Companywww.lightolier.com
631 Airport Road, Fall River, MA 02720 (508) 679-8131 Fax (508) 674-4710
We reserve the right to change details of design, materials and finish.
© 2003 Genlyte Thomas Group LLC (Lightolier Division) A0403
A. FOR OCTAGONAL OUTLET BOX (J-BOX), GEM BOX OR
SWITCH OUTLET BOX MOUNTING
1. Pull supply wires from OUTLET BOX through hole in
MOUNTING PLATE (Fig.1). Secure MOUNTING PLATE to
OUTLET BOX using screws provided with OUTLET BOX.
2. Insert tabs from OUTLET BOX COVERS into slots on
MOUNTING PLATE to enclose OUTLET BOX.
3. Pull supply wires through center hole in BACK PLATE . Align
BACK PLATE and mark holes for DRYWALL ANCHORS
(supplied), screw DRYWALL ANCHORS into wall.
4. Secure BACKPLATE to MOUNTING PLATE and DRYWALL
ANCHORS using screws provided.
5. While supporting BALLAST HOUSING, Make electrical
connections: Black lead or lead without tracer marks to
hot (Black) supply lead; White lead or lead with tracer
marks to neutral (White) supply lead. Uninsulated wire is
a ground wire and must be connected to grounding
terminal or ground lead inside OUTLET BOX. Use WIRE
NUTS.
6. Carefully push connections back into the OUTLET BOX.
7. Align tabs at top of BALLAST HOUSING with slots on BACK
PLATE, snap in and push housing flush with wall.
CAUTION: MAKE CERTAIN THAT NO WIRES ARE
PINCHED BETWEEN MOUNTING PLATE AND FIXTURE
BODY.
8. Insert ALLEN HEAD SCREW (provided) into hole at bottom
of BALLAST HOUSING and fasten BALLAST HOUSING to
BACK PLATE (Fig. 1)
B. FOR DIFFUSER ATTACHMENT
Glass Diffuser:
Secure DIFFUSER to BALLAST HOUSING
with Philips head glass mounting screws
(provided)
See Figs. 1 & 2.
Acrylic Diffuser:
1. Press PROTECTIVE BUSHINGS (supplied) through holes in
ACRYLIC DIFFUSER.
2. Proceed as above
Glass Diffuser
instructions.
NOTE:
If fixture is to be mounted without DIFFUSER, insert
gray plastic push-in plugs (supplied) to cover glass mtg.holes in
BALLAST HOUSING.
C. FOR FRONT COVER ATTACHMENT
1. After inserting Lamp, Snap the FRONT COVER onto end caps
of BALLAST HOUSING (Fig. 1).
2. Insert ALLEN HEAD SCREWS into the holes at both ends of
the fixture to secure front cover to BALLAST HOUSING.
D. To remove glass / acrylic for cleaning
1. Remove FRONT COVER by unscrewing ALLEN HEAD
SCREWS at both end caps and unsnap FRONT COVER from
end caps.
2. Remove lamp by rotating 90 degrees and gently pulling it out of
the sockets.
3. Unfasten DUFFUSER (if used) from the BALLAST HOUSING.
Glass:
clean with a small amount of glass cleaner on soft
cloth to remove hand oils and dirt.
Acrylic:
clean with mild soap and water
.
FOR ELECTRICAL CONDUIT MOUNTING- see diagram and
instructions on page two.
1 of 2
PROTECTIVE BUSHING
INSTALLATION FOR
ACRYLIC DIFFUSER
Read and understand these instructions before installing luminaire.
This luminaire is intended for installation in accordance with the National Electrical Code and local regulations. To assure full compliance
with local codes and regulations, check with your local electrical inspector before installation. To prevent electrical shock, turn off electricity
at fuse box before proceeding.
Retain these instructions for maintenance reference.
Figure 2
Figure 1
