Job Information
Type:
Job Name:
Cat. No.:
Lamp(s):
Notes:
"JSQPSU3PBE'BMM3JWFS."t t'BY
We reserve the right to change details of design, materials and finish.
XXXMJHIUPMJFSDPN½1IJMJQT(SPVQt
Lighting Systems
LSBW-9
1BHFPG
-ZUFTQSFBEÜ-4#1BSBCPMJD8BMM.PVOU-JHIU51FS'PPU /PNJOBM4FDUJPO
#
Features
1. Housing:
Extruded alu
m
inu
m
. Die-cast end cap
m
echanically attached with
no exposed fasteners or hardware.
2. Lamping:
One T5, 28 or 54 watt (as specified) fluorescent la
m
p per 4-foot
no
m
inal section. Provided by others.
3. Reflector:
Precision die-for
m
ed, se
m
i-specular alu
m
inu
m
.
Electrical
Ballast
- <10% T.H.D., .98 ballast factor, pre-heat start. 18 gauge wire. Color-
coded quick connectors allow ease of connection for joiner
m
odules. For special
circuiting, consult factory. Factory installed ballast disconnect allows the ballast
to be disconnected fro
m
and reconnected to inco
m
ing power under load without
turning the entire circuit off.
Dimming
- 120/277 VAC, 1% di
mm
ing level.
Emergency Battery Pack
- 28 Watt: 520 Lu
m
ens @ 90
m
in.
54 Watt: 700 Lu
m
ens @ 90
m
in.
Ordering Instructions
Individual Fixtures:
1. Order nu
m
ber of MODULES required.
2. Order one END SET per MODULE.
Continuous Rows:
1. Deter
m
ine run length.
2. Order the appropriate nu
m
ber of MODULES to co
m
plete the run.
3. Order one END SET per run.
Labels
UL, cUL and I.B.E.W.
Co
m
plete ordering instructions below.
Ordering Information
Type
La
m
ps
Length
Shielding
Ballast
Voltage
Finish
1
= 1-La
m
p T5
4
= 4-Foot
C
= Parabolic Louver
28
= 28W T5
1
= 120 Volt
AL
= Alu
m
inu
m
8
= 8-Foot
54
= 54W T5
2
= 277 Volt
WH
= White
5E
= 54W T5 E
m
ergency Pack
2E
= 28W T5 E
m
ergency Pack
5D
= 54W T5 Di
mm
ing
LSBW
1
C
Mountings
Dual-screw, draw-tight connector to create hairline sea
m
between joiner
m
odules.
Finish
Powder coated baked white or alu
m
inu
m
finish.
Custo
m
colors available, consult factory.
4. Shielding:
Parabolic louver, low-iredescent, se
m
i-specular anodized alu
m
inu
m
41” (104.14c
m
) shielding lengthwise, blades are 1-1/3” (3.39c
m
) high and 2”
(5.08c
m
) O.C. Louver fra
m
e is extruded alu
m
inu
m
and finished to
m
atch housing.
4 wire feed required.
11-3/8" (28.89c
m
)
8-1/2" (21.59c
m
)
1-3/4"
(4.45c
m
)
1
2
4
3-1/2" (8.89c
m
)
3
2-5/8"
(6.67c
m
)
