Job Information
Type:
Job Name:
Cat. No.:
Lamp(s):
Notes:
"JSQPSU3PBE'BMM3JWFS."t t'BY
We reserve the right to change details of design, materials and finish.
XXXMJHIUPMJFSDPN½1IJMJQT(SPVQt
Lighting Systems
LSB-8
1BHFPG
-ZUFTQSFBEÜ-4#1JFSDFE-VNJOPVT*OEJSFDU-JHIU51FS'PPU /PNJOBM4FDUJPO
#
Features
1. Housing:
Extruded alu
m
inu
m
. Die-cast end cap
m
echanically attached with
no exposed fasteners or hardware.
2. Lamping:
3. Reflector:
Precision die-for
m
ed se
m
i-specular alu
m
inu
m
.
4. Shielding:
Precision die-for
m
ed, pierced 20 gauge CRS. Piercing is four rows
that extend the entire length of the la
m
ps. The pattern is 5/8” (1.59c
m
) x 1/16”
(0.16c
m
) slot with a 3/16” (0.48c
m
) separation between rows.
Electrical
Ballast is <10% THD, .98 ballast factor, pre-heat start. 18 gauge wire. Color-
coded quick connectors allow ease of connection for joiner
m
odules. Power feed
is 18 gauge white SJT. For special circuiting consult factory. Factory installed
ballast disconnect allows the ballast to be disconnected fro
m
and reconnected to
inco
m
ing power under load without turning the entire circuit off.
Dimming:
120/277 VAC 1% di
mm
ing level, 4 wire feed required.
Emergency Battery Pack:
28 watt: 520 lu
m
ens @ 90
m
inutes, 54 watt: 700
lu
m
ens @ 90
m
inutes, 4 wire feed required.
Mountings
Finish
Powder coated baked white or alu
m
inu
m
finish. Custo
m
colors available, consult
factory.
Labels
UL, cUL and I.B.E.W.
Ordering Instructions
Individual Fixtures:
1. Order nu
m
ber of MODULES required.
2. Order one POWER FEED END SET per MODULE.
Continuous Rows:
1. Deter
m
ine run length.
2. Order the appropriate nu
m
ber of MODULES for the co
m
plete run.
3. Order one POWER FEED END SET per run.
4. Order one CABLE ASSEMBLY per MODULE
m
inus one per run.
5. For runs that exceed a
m
perage li
m
its, order the appropriate nu
m
ber of
CABLE/CORD ASSEMBLIES.
Options and Accessories
E
m
ergency Circuiting; special circuiting; X, T & L joiner blocks - consult factory.
Co
m
plete ordering instructions below.
Cable suspension (not shown) - 4-1/2" (11.43c
m
) dia
m
eter canopy finished white
ena
m
el, 1/16" (0.16c
m
) dia
m
eter stainless steel aircraft cable adjustable up to 36"
(91.44c
m
). Dual-screw draw-tight connector to create hairline sea
m
between joiner
m
odules.
Ordering Information
Fa
m
ily
La
m
ps
Voltage
Finish
2
= 2-La
m
p T8
B
= Pierced
AL
= Alu
m
inu
m
WH
= White
LSB
2
B
Length
Shielding
Ballast
1
= 120 volt
2
= 277 volt
32
= 32W T8
3E
= 32W T8 E
m
ergency Pack
3D
= 32W T8 Di
mm
ing
Two T8 32 watt fluorescent la
m
ps per 4-Foot section.
Provided by others.
4
= 4-Foot
8
= 8-Foot
Pierce Pattern
3/16"
(0.48c
m
)
5/8"
(1.59c
m
)
3-1/16"
(7.78c
m
)
1/16"
(0.16c
m
)
1
3
4
Fixture Shown Half Scale
2
3-1/2" (8.89c
m
)
8-1/2” (21.59c
m
)
1-3/4" (4.45c
m
)
