background image

-  5

-

A.  High Level (Speaker) Inputs : 

The high level inputs use a detachable connector terminated with 20 AWG leads.

These inputs should be used if the source unit has only speaker line (high level) outputs and not RCA outputs.

B. RCA Input Jacks – Line Level from Radio Pre-outs: 

The industry standard RCA jack provides an easy connection

for signal level input. They are gold-plated to resist the signal degradation caused by corrosion.

C. Gain Control: 

The input gain control is preset to  match the output of most source units. They can be adjusted to

match output levels from a variety of source units.

D.  Crossover Filter Switch:

High

for High Pass - Mid-Tweeter.

Off

for All Pass - Full Range.

Low

for Low Pass - Subs.

E.  Speaker Connections:  

Follow correct polarity, and do not Ground any speaker wires. Do not connect any speaker

wires together.

F.  Power Connector Plug: 

Connects Power, Ground, and Remote

G. Power Cell (Capacitor) Plug: 

Power Cell has 2 active leads for B+ and Ground

H. Power 

Fuse: 

If this Fuse should blow, determine the cause or see your authorized dealer. 

Never

replace the fuse

with one of greater value than the original

I. 

Adjustable Crossover Frequency Control: 60-400Hz.

J.  Juice Boost Switch: 

Applies 6dB of 50Hz Bass Boost. 

K

Juice Boost Remote Module

: The Juice Boost remote module has a Green “Operation” indicator and Red

“Protection” indicator. The Remote Juice Boost Module allows adjustment of the overall gain or volume of the
amplifier. It operates only when the crossover switch is in Low Pass position. It does not alter the frequency
response, but instead allows control of the overall gain of the amplifier driving your woofers. Most experienced
users adjust the Juice Boost knob on the amp for the maximum desired amount of bass boost, and then plug
in the module to control how much of that boost they want to unleash to their subwoofers.

L. Pass Thru Outputs:

The Pass-Thru provides a convenient source for daisy-chaining an additional amplifier without

running and extra set of RCA cables from the front of the vehicle to the rear amplifier location.

M. Juice Boost:

Applies 0-12dB of 50Hz Bass Boost.

Design  FeAtures

ChecK  our  website 

www.LightningAudio.com

for  updAtes  on  your  products.

Содержание S2.200





























Отзывы: