background image

 

 

Always make sure that you are connecting to the proper voltage and that the line 
voltage you are connecting to is not higher than that stated on the rear panel of the 
fixture. 

 

This is an IP65 rated outdoor fixture. To prevent damage to the waterproof seal, 
do not pull the product apart yourself. Refer to qualified person. 

 

Make sure there are no flammable materials close to the unit while operating. 

 

The  unit  must  be  installed  in  a  location  with  adequate  ventilation,  at  least  50cm 
from adjacent surface. Be sure that no ventilation slots are blocked. 

 

Always  disconnect  from  power  source  before  servicing  or  replacing  fuse  and  be 
sure to replace with same fuse source. 

 

Secure  fixture  to  fastening  device  using  a  safety  chain.  Never  carry  the  fixture 
solely by its head. Use its carrying handles. 

 

In the event of serious operating problem, stop using the unit immediately. Never 
try to repair the unit by yourself. Repairs carried out by unskilled people can lead 
to  damage  or  malfunction.  Please  contact  the  nearest  authorized  technical 
assistance center. Always use the same type spare parts. 

 

Never connect the device to a dimmer pack.  

 

Make sure power cord is never crimped or damaged. 

 

Never disconnect power cord by pulling or tugging on the cord. 

 

Avoid direct eye exposure to the light source while it is on. 

 

INSTALLATION: 

CAUTION

: For safe mounting, read the following 

instructions carefully:  

 

Use  suitable  hook  clamps  for  hanging  the  lighting 
effect.  

 

Use  a  safety  wire  with  a  breaking  strain  of  more  than 
double the lighting effect.  

 

Do not look directly into the light source.  

 

Make sure the lighting effect has suitable ventilation as 
per the instructions below. 

 

This  lighting  effect  is  intended  for  indoor  use  only  to 
avoid  electrical  shock  keep  away  from  rain  and 
moisture.  

 

Keep unit out of reach from children.  

 

NOTE

: Use washers and spring washers when attaching your hook clamp to the yoke. 

 
1.

 

For installation of the hook clamps and safety wire.  

2.

 

This lighting effect must be 0.5m away from any flammable materials or any walls or 
ceilings.  

3.

 

Do not block or inhibit the air flow from the ventilation vents. 

Содержание P645QUADO








Отзывы: