Liftsafe Fall Protection RoofStep 3x1 LD Скачать руководство пользователя страница 1

Страница: 1 / 12

Guardrail System

Model Numbers:

RoofStep 5x5 XS, RoofStep 5x4 XS,

RoofStep 5x3 LD, RoofStep 5x2 LD,
RoofStep 5x1 LD, RoofStep 4x4 XS,
RoofStep 4x3 LD, RoofStep 4x2 LD,
RoofStep 4x1 LD, RoofStep 3x3 XS,

RoofStep 3x2 LD, RoofStep 3x1 LD

LIFTSAFE

Installation Manual:

RoofGuard RoofStep Ladder Series
RoofGuard RoofStep Crossover Series
Gargoyle Ladder Series
Gargoyle Crossover Series

This Installation Manual is intended to meet the Manufacturer’s Instructions requirements and should be used as part of

an employee training program.

WARNINGS AND CONDITIONS

These instructions must be provided to the installer of this system. The installer must read and understand these

instructions and follow.

Failure to follow these instructions or the details of the unique layout drawing provided may result in serious injury or

death. If you have any questions about this system’s use or care, please contact the manufacturer: 1-800-977-2005.

RoofStep Ladder Series Systems, RoofStep Crossover Series Systems, Gargoyle Ladder Series, Gargoyle
Crossover Series Manual RGC-RS

Содержание RoofStep 3x1 LD












